SCREAMIN' EAGLE PRO BILLET CAM PLATE WITH SUPER SUCKER OIL PUMP
941002212021-08-02
GENERAL INFORMATION
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
62400260, 62400264
Safety Glasses, Torque Wrench
3 Dark wrench
(1) Special tools or techniques required for installation
KIT CONTENTS
Figure 1. Kit Contents: Screamin' Eagle Pro Billet Cam Plate With Super Sucker Oil Pump
Table 2. Kit Contents: Screamin' Eagle Pro Billet Cam Plate With Super Sucker Oil Pump
Verify that all contents are present in the kit before installing or removing items from vehicle.
Item
Qty
Description
Part No.
Notes
1
2
Screw, 1/4-20 X 3/4 TORX button head, with lockpatch (Grade 8)
942
2
1
Tensioner
25500013
3
4
Screw, 1/4-20 X 2-3/4 knurled head, with lockpatch
4822A
4
1
Set screw
10201258
5
3
Plug
45830-48
6
1
Camshaft support
25400419
7
1
Dowel pin
16589-99A
8a
1
Oil pump gerotor, feed, oil cooled
62400006
8b
1
Oil pump gerotor, feed, twin cooled
62400274
9
1
Oil pump housing (assembly), oil cooled
62400261
Includes items: 8a and 10
1
Oil pump housing (assembly), twin cooled
62400266
Includes items: 8b and 10
10
1
Oil pump gerotor, scavenge
62400006
11
1
Back housing, oil pump
62400272
Includes item 12
12
1
Cover seal
62400205
13
1
Roll pin
601
14
1
Oil bypass valve
26400-82B
15
1
Spring
26210-99
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
This part is available at a Harley-Davidson dealership.
  • Separate purchase of Scavenge Port O-ring is required. See vehicle parts catalog or Harley-Davidson dealership.
  • Separate purchase of Oil Feed Port O-ring is required. See vehicle parts catalog or Harley-Davidson dealership.
PREPARE
1. Disconnect negative battery cable. See service manual.
REMOVE
1. Remove Original Equipment (OE) camshaft support plate and discard. See service manual.
a. Keep short screws.
b. Discard long screws.
2. See Figure 2. Remove OE oil pump assembly and discard. See service manual.
a. Discard scavenge port O-ring (5).
b. Discard oil seal (6).
INSTALL
Oil Pump
1. Lubricate all parts with assembly lube during assembly.SCREAMIN' EAGLE ASSEMBLY LUBE (11300002)
2. See Figure 2. Install back housing (4) and scavenge gerotor set (3) onto crankshaft.
3. Install new O-ring (5) in crankcase scavenge port.
4. Apply assembly lube to scavenge port spigot.SCREAMIN' EAGLE ASSEMBLY LUBE (11300002)
5. Slide oil pump housing (2) onto crankshaft while fitting scavenge port into O-ring (5).
a. Firmly push on oil pump housing to fully seat.
6. Install feed gerotor set (1).
1Feed gerotor set
2Oil pump housing
3Scavenge gerotor set
4Back housing
5Scavenge port O-ring
6Oil seal
Figure 2. Oil Pump
Camshaft Support Plate
1. Apply assembly lube to all bearing surfaces and bearings.SCREAMIN' EAGLE ASSEMBLY LUBE (11300002)
2. See Figure 3. Install camshaft support plate.
a. Verify camshaft is in crankcase.
b. Install new O-ring (4) into crankcase feed oil port.
c. Apply assembly lube to cam support plate feed oil port.SCREAMIN' EAGLE ASSEMBLY LUBE (11300002)
d. Slide camshaft support plate (5) over shafts and mate to crankcase.
e. Verify camshaft support plate (5) is fully seated.
NOTE
Long screws (2) are used for oil pump housing.
f. Start all screws (1, 2).
3. See Figure 4. Tighten screws in sequence.
a. Tighten screws (1, 2).
Torque: 1.4–6.8 N·m (12–60 in-lbs) 1st torque
b. Rotate crankshaft one full revolution (360 degrees).
c. Tighten screws (3-8) in sequence shown.
Torque: 10.2–13.6 N·m (90–120 in-lbs) 2nd torque
d. Final tighten four oil pump screws (1-2, 9-10) in same sequence.
Torque: 1.4–13.6 N·m (12–120 in-lbs) 3rd torque
1Short screw (6)
2Long screw (4)
3Camshaft
4O-ring
5Support plate
Figure 3. Camshaft Support Plate
Figure 4. Camshaft Support Plate Tightening Sequence
Camshaft Drive
1. Install camshaft drive assembly. See service manual.
a. See Figure 1. Install tensioner (2) from kit.
COMPLETE
1. Install any miscellaneous components that were previously removed. See service manual.
2. Connect negative battery cable. See service manual.