SCREAMIN' EAGLE PRO BILLET CAM PLATE WITH SUPER SUCKER OIL PUMP
941002212021-08-02
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
62400260, 62400264 | Safety Glasses, Torque Wrench |  3 Dark wrench
|
(1) Special tools or techniques required for installation
KIT CONTENTS
Figure 1. Kit Contents: Screamin' Eagle Pro Billet Cam Plate With Super Sucker Oil Pump
Table 2. Kit Contents: Screamin' Eagle Pro Billet Cam Plate With Super Sucker Oil Pump
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 2 | Screw, 1/4-20 X 3/4 TORX button head, with lockpatch (Grade 8) | 942 | |
| 2 | 1 | Tensioner | 25500013 | |
| 3 | 4 | Screw, 1/4-20 X 2-3/4 knurled head, with lockpatch | 4822A | |
| 4 | 1 | Set screw | 10201258 | |
| 5 | 3 | Plug | 45830-48 | |
| 6 | 1 | Camshaft support | 25400419 | |
| 7 | 1 | Dowel pin | 16589-99A | |
| 8a | 1 | Oil pump gerotor, feed, oil cooled | 62400006 | |
8b | 1 | Oil pump gerotor, feed, twin cooled | 62400274 | ||
| 9 | 1 | Oil pump housing (assembly), oil cooled | 62400261 | Includes items: 8a and 10 |
1 | Oil pump housing (assembly), twin cooled | 62400266 | Includes items: 8b and 10 | ||
| 10 | 1 | Oil pump gerotor, scavenge | 62400006 | |
| 11 | 1 | Back housing, oil pump | 62400272 | Includes item 12 |
| 12 | 1 | Cover seal | 62400205 | |
| 13 | 1 | Roll pin | 601 | |
| 14 | 1 | Oil bypass valve | 26400-82B | |
| 15 | 1 | Spring | 26210-99 | |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
This part is available at a Harley-Davidson dealership.
- Separate purchase of Scavenge Port O-ring is required. See vehicle parts catalog or Harley-Davidson dealership.
- Separate purchase of Oil Feed Port O-ring is required. See vehicle parts catalog or Harley-Davidson dealership.
PREPARE
| 1. | Disconnect negative battery cable. See service manual. |
REMOVE
| 1. | Remove Original Equipment (OE) camshaft support plate and discard. See service manual. a. Keep short screws. b. Discard long screws. | |
| 2. | Figure 2 Remove OE oil pump assembly and discard. See service manual. a. Discard scavenge port O-ring (5). b. Discard oil seal (6). |
INSTALL
Oil Pump
| 1. | Lubricate all parts with assembly lube during assembly.SCREAMIN' EAGLE ASSEMBLY LUBE (11300002) | |
| 2. | Figure 2 Install back housing (4) and scavenge gerotor set (3) onto crankshaft. | |
| 3. | Install new O-ring (5) in crankcase scavenge port. | |
| 4. | Apply assembly lube to scavenge port spigot.SCREAMIN' EAGLE ASSEMBLY LUBE (11300002) | |
| 5. | Slide oil pump housing (2) onto crankshaft while fitting scavenge port into O-ring (5). a. Firmly push on oil pump housing to fully seat. | |
| 6. | Install feed gerotor set (1). |
| 1 | Feed gerotor set |
| 2 | Oil pump housing |
| 3 | Scavenge gerotor set |
| 4 | Back housing |
| 5 | Scavenge port O-ring |
| 6 | Oil seal |
Figure 2. Oil Pump
Camshaft Support Plate
| 1. | Apply assembly lube to all bearing surfaces and bearings.SCREAMIN' EAGLE ASSEMBLY LUBE (11300002) | |
| 2. | Figure 3 Install camshaft support plate. a. Verify camshaft is in crankcase. b. Install new O-ring (4) into crankcase feed oil port. c. Apply assembly lube to cam support plate feed oil port.SCREAMIN' EAGLE ASSEMBLY LUBE (11300002) d. Slide camshaft support plate (5) over shafts and mate to crankcase. e. Verify camshaft support plate (5) is fully seated. NOTE Long screws (2) are used for oil pump housing. f. Start all screws (1, 2). | |
| 3. | Figure 4 Tighten screws in sequence. a. Tighten screws (1, 2). Torque: 1.4–6.8 N·m (12–60 in-lbs) 1st torque b. Rotate crankshaft one full revolution (360 degrees). c. Tighten screws (3-8) in sequence shown. Torque: 10.2–13.6 N·m (90–120 in-lbs) 2nd torque d. Final tighten four oil pump screws (1-2, 9-10) in same sequence. Torque: 1.4–13.6 N·m (12–120 in-lbs) 3rd torque |
| 1 | Short screw (6) |
| 2 | Long screw (4) |
| 3 | Camshaft |
| 4 | O-ring |
| 5 | Support plate |
Figure 3. Camshaft Support Plate
Figure 4. Camshaft Support Plate Tightening Sequence
Camshaft Drive
| 1. | Install camshaft drive assembly. See service manual. a. Figure 1 Install tensioner (2) from kit. |
COMPLETE
| 1. | Install any miscellaneous components that were previously removed. See service manual. | |
| 2. | Connect negative battery cable. See service manual. |