PILLION KIT

941001742023-09-15

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
52400271, 52400251	Safety Glasses, Torque Wrench, Loctite 243 blue

(1) Tightening to torque value or other moderate tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Pillion 48X Kit

Table 2. Pillion 48X Kit

Verify that all contents are present in the kit before installing or removing items from vehicle.
Item	Qty	Description	Part No.	Notes
1	1	Pillion	Not sold separately
2	1	Spacer	52400301
3	1	Rain guard	59500915
4	2	Screw	10201249
5	3	Screw	10201248
6	2	Washer, small	10300078
7	2	Washer, large	10300233
8	1	Grab strap	52400270

GENERAL

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

WARNING

Do not install these seat kits on motorcycles that are not equipped with an appropriate grab strap and passenger footpegs. If footpegs and grab strap are not installed, passenger could fall from moving motorcycle or grab onto operator, causing loss of control and death or serious injury. (00410b)

WARNING

Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)

NOTE

This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:

A Harley-Davidson dealer.
H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.

REMOVE

1.	Remove Original Equipment (OE) seat. See service manual.
2.	Remove rear fender cowl and rear fender halves. Discard cowl and retain rear fender halves. See service manual.
3.	Remove rear fender console grommet. Discard.

INSTALL

1.	See Figure 2. Install rain guard (1). a. Tighten screws (2). Torque: 20.3 N·m (180 in-lbs)
2.	Install right and left rear fender halves. See service manual.
3.	See Figure 3. Install grab strap. a. Remove OE screw (2). Retain. b. Apply threadlocker to screw (2).LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97) c. See Figure 3. Install grab strap (1), washer (3) and OE screw (2). Tighten. Torque: 4.3–5.2 N·m (38–46 in-lbs)
4.	See Figure 4. Install spacer (1).
5.	See Figure 5. Install pillion (2) through grab strap (1).
6.	See Figure 6. Install washers (2) and two screws (3).
7.	Apply threadlocker to screw (3).LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97)
8.	See Figure 6. Install washer (1) and screw (3). Tighten. Torque: 11–13.6 N·m (97–120 in-lbs)
9.	Install seat. NOTE Wiggling OE seat back and forth will aid in installation. Some slight force is required. Key may need to be turned so that pin on seat will interact with lock on vehicle. a. See Figure 5. Align pillion tabs (3) with OE seat slots (5). b. After installing seat, pull up on seat to verify that it is secure. See service manual.

1	Rain guard
2	Screw (2)

Figure 2. Fender, Rain Guard

1	Grab strap
2	OE Screw
3	Washer, large

Figure 3. Grab Strap

1	Spacer
2	Rain guard

Figure 4. Spacer

1	Grab strap
2	Pillion
3	Tab, pillion (2)
4	Seat
5	Slot, seat (2)
6	Rain guard
7	Fender half, left side

Figure 5. Pillion

1	Washer, large
2	Washer, small (2)
3	Screw (3)

Figure 6. Secure Pillion Spacer and Pillion