H-D AUDIO POWERED BY ROCKFORD FOSGATE - PRIMARY AND SECONDARY SUB WOOFER KIT
941003142022-01-18
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
76001163, 76001164 | Safety glasses, torque wrench, power drill, drill bit set (including 25/64-inch and 3/4-inch), masking tape, deburring tool, isopropyl alcohol, clean shop rags, appropriate cutting tool (reciprocating saw or hand saw) |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Sub Woofer, Primary (Right Saddlebag)
Figure 2. Kit Contents: Sub Woofer, Secondary, (Left Saddlebag)
Table 2. Kit Contents: Sub Woofer
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Sub woofer, primary (right saddlebag) | Not sold separately | |
1 | Sub woofer, secondary (left saddlebag) | Not sold separately | |||
| 2 | 2 | Washer, EPDM | 57765-99 | |
| 3 | 1 | Plug panel, right | 76001188 | |
1 | Plug panel, left | 76001176 | |||
| 4 | 2 | Thumb screw | 10500211 | |
| 5 | 1 | Drill template, right saddlebag | 76001189 | |
1 | Drill template, left saddlebag | 76001177 | |||
| 6 | 1 | Internal harness | 69203012 | |
| 7 | 1 | External harness, primary (right saddlebag) | 69203031 | |
| 1 | External harness, secondary (left saddlebag) | 69203032 | ||
| 8 | 6 | Cable strap | 10065 | |
| 9 | 6 | Retainer | 69200342 | |
| 10 | 1 | Label, saddlebag fastener | 14003212 | |
| 11 | 1 | Inner bezel, right | 76001186 | |
| 1 | Inner bezel, left | 76001185 | ||
| 12 | 1 | Outer bezel assembly, right | 76001187 | |
| 1 | Outer bezel assembly, left | 76001175 | ||
| 13 | 1 | Screw, saddlebag mount | 10201365 | |
| 14 | 8 | Screw | 10201347 | |
| 15 | 1 | Top enclosure panel, right | 76001170 | |
| 1 | Top enclosure panel, left | 76001193 | ||
| 16 | 3 | Tapping screw | Not sold separately | |
Items mentioned in text, but not included in kit | |||||
| A | 1 | Right saddlebag | ||
| B | 1 | Left saddlebag | ||
NOTE
Verify all contents are present in the kit before installing or removing items from vehicle.
GENERAL
NOTE
The newly installed audio system and speakers will not play audio unless it is configured using the Harley-Davidson audio app or by an authorized Harley-Davidson dealership.
NOTE
The various generations of speakers, amplifiers and wiring for Harley-Davidson vehicles were not designed or tested to work together. Refer to the P&A catalog for fitment recommendations and consult your dealership to ensure optimal performance and compatibility.
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Electrical Overload
WARNINGWhen installing any electrical accessory, be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modified. Exceeding the maximum amperage can lead to electrical failures, which could result in death or serious injury. (00310a)
NOTICE
It is possible to overload the vehicle's charging system by adding too many electrical accessories. If the combined electrical accessories operating at any one time consume more electrical current than the vehicle's charging system can produce, the electrical consumption can discharge the battery and cause damage to the vehicle's electrical system. (00211d)
See Figure 3 , Figure 4 , Figure 7 and Figure 5. The subwoofer systems require two channels from the amplifier (amplifiers are four channels) therefore installing both primary and secondary subwoofer kits can only work with two or four speaker systems. Six speaker systems will only work with the primary subwoofer kit.
Figure 3. Single Subwoofer, Single Amplifier, Two Speakers
Figure 4. Single Subwoofer, Dual Amplifiers, Four Speakers
Figure 5. Single Subwoofers, Dual Amplifiers, Six Speakers
Figure 6. Dual Subwoofers, Dual Amplifiers, Two Speakers
| 1 | Front speakers (fairing) |
| 2 | 2nd Set of speakers (fairing lowers, saddlebags, Tour-Pak) |
| 2a | 3rd Set of speakers (fairing lowers, Tour-Pak) |
| 3 | Primary amplifier |
| 4 | Right subwoofer (primary) |
| 5 | Secondary amplifier |
| 6 | Left subwoofer (secondary) |
Figure 7. Dual Subwoofers, Dual Amplifiers, Four Speakers
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
NOTE
The saddlebag(s) must be completely empty of any loose items or P&A installed components like the Saddlebag Wall Organizer or Premium Fitted Saddlebag Lining.
These items are available at your Harley-Davidson dealership:
- 2014-2016 CVO and Touring (except FLHRC) Separate purchase of Harley-Davidson Saddlebag Mount Lever Kit (Part No. 90201540) is required for this installation. Two lever screws from kit will be needed to install saddlebag.
- 2014 and Later FLHTKSE, FLTRUSE and Touring: Separate purchase of Harley-Davidson Primary Amplifier Kit (Part No. 76000974) is required for this installation.
- 2014 and Later FLHTKSE, FLTRUSE and Touring: Separate purchase of Harley-Davidson Primary Amplifier and Dongle Kit (Part No. 76000997) is required for this installation.
- 2014 and Later FLHTKSE, FLTRUSE and Touring: Separate purchase of Harley-Davidson Secondary Audio Amplifier Kit (Part No. 76000990) may be required for this installation.
- 2014 and Later FLHTKSE, FLTRUSE and Touring: Separate purchase of Harley-Davidson Secondary Amplifier Installation Kit (Part No. 76000975) may be required for this installation.
- 2014 and Later FLHTKSE, FLTRUSE and Touring: Separate purchase of Harley-Davidson Fairing Speaker Harness Install Kit (Part No. 76001100) may be required for this installation.
- 2021 and Later FLHXSE and FLTRXSE: Separate purchase of Harley-Davidson Bluetooth Dongle (Part No. 41000771) is required for this installation. For use with Harley-Davidson audio app.
- 2021 and Later FLHXSE and FLTRXSE: Separate purchase of Harley-Davidson Secondary Audio Amplifier Kit (Part No. 76000990) is required for this installation.
- 2021 and Later FLHXSE and FLTRXSE: Separate purchase of Harley-Davidson Secondary Amplifier Installation Kit (Part No. 76000975) is required for this installation.
- 2021 and Later FLHXSE and FLTRXSE: Separate purchase of Harley-Davidson Dual Lock Tape (Part No. 76434-06) is required for this installation.
- 2022 and Later FLTRKSE: Separate purchase of Harley-Davidson Bluetooth Dongle (Part No. 41000771) is required for this installation. For use with Harley-Davidson audio app.
- 2022 and Later FLTRKSE: Separate purchase of Harley-Davidson Secondary Amplifier Installation Kit (Part No. 76000975) is required for this installation.
- 2022 and Later FLTRKSE: Separate purchase of Harley-Davidson Bluetooth Dongle (Part No. 41000771) is required for this installation. For use with Harley-Davidson audio app.
- Digital Technician II (DT II)may be required to check and update amplifier software. Contact your local Harley-Davidson dealership.
- Vehicle's equipped with Boom!™ Box 4.3 radio, DT IImay be required to update software. Contact your local Harley-Davidson dealership.
- Vehicle's equipped with Boom!™ Box 6.5 GT radio, DT IImay be required to update software. Contact your local Harley-Davidson dealership.
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
Installation by a technician at a Harley-Davidson dealership is recommended.
PREPARE
| 1. | Remove both saddlebags. See service manual. | |
| 2. | Remove side covers. See service manual. | |
| 3. | Remove main fuse. See service manual. | |
| 4. | Remove seat. See service manual. | |
| 5. | Remove left side caddy. See service manual. | |
| 6. | Remove top caddy. See service manual. | |
| 7. | Remove lower backbone caddy. See service manual. |
SADDLEBAGS
Right Saddlebag
| 1. | Figure 8 Position drill template on right saddlebag. NOTE Do not modify left saddlebag unless a second subwoofer is being installed. a. Mask off entire drill template (2) area on right saddlebag (1) with masking tape. b. Install drill template (2). c. Secure entire perimeter of drill template (2) with tape. d. Install tapping screws (3) to hold down drill template (2). | |
| 2. | Figure 9 Using a marker, trace drill template outline (1) onto saddlebag's masking tape. | |
| 3. | Figure 8 Modify right saddlebag (1). a. Drill pilot holes in drill locations (4, 5, 6) using 1/8-inch drill bit. b. Relief Holes: Drill six 25/64-inch relief holes (4). c. Screw Holes: Drill eight 25/64-inch screw holes (6). NOTE When riding in rain, water will potentially come through the bezel grille. Drain hole is required for water drainage. d. Figure 10 Drainage Holes: Drill two 1/4-inch drainage holes (3) in the approximate location. e. Figure 9 With drill template still in place and using an appropriate saw, cut along the outer part of template outline (1). f. Remove tapping screws (3), drill template and tape from saddlebag. g. Grommet Hole: Drill 3/4-inch grommet hole (5) where tapping screw (3) was removed. h. Deburr holes and template outline by lightly sanding the surface. i. Clean all surfaces of the body work with 50-70% isopropyl alcohol and 30-50% distilled water. Allow to dry completely. | |
| 4. | Figure 1 Install saddlebag fastener label (10). a. Install label near rear mounting lever screw. | |
| 5. | Figure 11 Test fit inner (2) and outer (1) bezels on saddlebag. a. Install and lightly tighten screws (8). b. Make sure components fit properly. c. Remove screws and bezels (1, 2). d. Make adjustments as needed. | |
| 6. | Remove VHB tape backing from bezel. | |
| 7. | Figure 12 Apply silicone caulk (3) to inner (1) and outer (2) bezels. NOTE To assist in preventing water intrusion in saddlebag, silicone caulk is applied as an extra measure of protection. | |
| 8. | Figure 11 Install inner (2) and outer (1) bezels on saddlebag. a. Install screws (3). NOTE DO NOT over tighten bezel screws. b. Figure 13 Tighten in sequence. Torque: 0.4–0.6 N·m (4–5 in-lbs) Bezel screws | |
| 9. | Figure 14 To maximize seal performance, use wooden wedges on inner bezel (1). Hold in place for 24 hours. a. For maximum corner adhesion, place wooden wedge in area as directed by arrow. | |
| 10. | Figure 15 Install harness 69203012 (5) into right saddlebag. a. Figure 17 Rotate grommet until proper harness routing is achieved. | |
| 11. | Figure 15 Connect harness 69203031 (4) to harness 69203012 (5). NOTE Kit 90201540 needs to be installed for securing saddlebags. See Installation Requirements | |
| 12. | Install right saddlebag. a. Install OE rear saddlebag mount screw. b. Figure 1 Install saddlebag front mount screw (13) from kit. Tighten. Torque: 5–5.6 N·m (44–50 in-lbs) Saddlebag front mount screw | |
| 13. | Connect harness 69203031 to: a. Figure 3 For single subwoofer, single amplifier and two speaker setup. Harness connector will need to be rewired. Rewire Harness 69203031 Failure to rewire connector will result in no audio. NOTE: If saddlebag speakers are added after subwoofer is installed, the original configuration of harness 69203031 will have to used. Wires in cavities one and four. b. Primary amplifier harness connector [351A] (audio out). Figure 3 Equipped with Single Subwoofer, Single Amplifier, Two Speakers. c. Secondary amplifier harness connector [352A_1] or [352A_2] (audio out). Figure 4 Equipped with Single Subwoofer, Dual Amplifiers, Four or Six Speakers. | |
| 14. | Figure 16 Route and secure harnesses with cable straps. a. Make sure harnesses do not interfere with moving parts. b. Use factory harness anchor points. | |
| 15. | Figure 19 Install subwoofer (2). | |
| 16. | Figure 15 Connect harness 69203012 (5) into subwoofer connector (2). Figure 19 | |
| 17. |
| 1 | Right saddlebag |
| 2 | Drill template |
| 3 | Tapping screw (3) |
| 4 | 25/64-inch relief hole (6 drilled) |
| 5 | 3/4-inch grommet hole (1 drilled) |
| 6 | 25/64- inch screw hole (8 drilled) |
Figure 8. Right Saddlebag Drill Template
| 1 | Template outline |
Figure 9. Template Outline
| 1 | Left saddlebag |
| 2 | Right saddlebag |
| 3 | ¼-inch drain hole locations |
Figure 10. Drainage Hole Placement
| 1 | Outer bezel |
| 2 | Inner bezel |
| 3 | Screw (8) |
Figure 11. Test Fit Bezels
| 1 | Inner bezel |
| 2 | Outer bezel |
| 3 | Silicone caulk |
Figure 12. Bezels
Figure 13. Torque Sequence - Bezel Screws
| 1 | Inner bezel |
| 2 | Wood blocks (2) |
Figure 14. Wooden Wedge
| 1 | Harness 69203012 |
| 2 | Outline of left saddlebag |
| 3 | Harness 69203032 |
| 4 | Harness 69203031 |
| 5 | Harness 69203012 |
| 6 | Outline of right saddlebag |
Figure 15. Subwoofer Harness Routing
| 1 | Anchor point |
| 2 | Rear fender strut |
Figure 16. Rear Fender Strut
| 1 | Right saddlebag |
| 2 | Harness routing |
| 3 | Grommet (Harness 69203012) |
Figure 17. Right Saddlebag Harness Routing
| 1 | Right saddlebag |
| 2 | Outer bezel |
| 3 | Grille |
Figure 18. Outer Bezel
| 1 | Right subwoofer |
| 2 | Subwoofer connector |
| 2 | Right saddlebag |
Figure 19. Install Subwoofer
Left Saddlebag
| 1. | Figure 20 Repeat procedures 1-8 from right saddlebag. | |
| 2. | Figure 15 Install harness 69203012 (5) into right saddlebag. a. Figure 17 Rotate grommet until proper harness routing is achieved. | |
| 3. | Figure 15 Connect harness 69203032 (3) to harness 69203012 (5). | |
| 4. | Install left saddlebag. a. Install OE rear saddlebag mount screw. b. Figure 1 Install front saddlebag mount screw (13) from kit. | |
| 5. | Connect harness 69203032 to: a. Secondary amplifier harness connector [352A_1] or [352A_2] (audio out). Figure 7 Equipped with Dual Subwoofers, Dual Amplifiers, Four Speakers. | |
| 6. | Route and secure harnesses with cable straps. a. Make sure harnesses do not interfere with moving parts. b. Use factory harness mounting points. | |
| 7. | Figure 19 Install subwoofer (2). | |
| 8. | Figure 15 Connect harness 69203012 (5) into subwoofer connector (2). Figure 19 |
| 1 | Left drill template |
| 2 | 3/4 inch grommet hole (1 drilled) |
| 3 | Left saddlebag |
Figure 20. Left Saddlebag Drill Template
Remove Subwoofer
| 1. | Disconnect subwoofer. | |
| 2. | Remove subwoofer from saddlebag. | |
| 3. | Figure 1 Position EPDM washer (2) on inner side of plug panel (3). | |
| 4. | Figure 21 Position plug panel (1) over inner bezel. | |
| 5. | Install thumb screws (2). Tighten. |
| 1 | Plug panel |
| 2 | Thumb screw (2) |
| 3 | Right saddlebag |
Figure 21. Plug Panel
Rewire Harness 69203031
NOTE
This is for a special configuration. DO NOT alter harness unless instructed in procedure.
| 1. | 1. Figure 22 Use special tool to remove terminals from connector. Special Tool: MOLEX ELECTRICAL CONNECTOR TERMINAL REMOVER (HD-48114) | |
| 2. | Remove light-blue wire (5) from cavity one (1). | |
| 3. | Install light-blue wire (5) into cavity three (3). | |
| 4. | Remove light-blue/black wire (6) from cavity four (4). | |
| 5. | Install light-blue/black wire (6) into cavity two (2). |
| 1 | Cavity one |
| 2 | Cavity two |
| 3 | Cavity three |
| 4 | Cavity four |
| 5 | Light blue wire |
| 6 | Light blue/black wire |
Figure 22. Rewire Harness 69203031
COMPLETE
| 1. | Install lower backbone caddy. See service manual. | |
| 2. | Install top caddy. See service manual. | |
| 3. | Install left side caddy. See service manual. | |
| 4. | Install seat. See service manual. | |
| 5. | Install main fuse. See service manual. | |
| 6. | Install side covers. See service manual. | |
| 7. | Install both saddlebags. See service manual. |