SECURITY ANCHOR

941002862022-01-17

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
92800013	Safety Glasses, Heavy Duty Drill, Hammer, Vacuum Cleaner, Screwdrivers (Flat & Phillips head), Felt Marker

(1) Special tools or techniques required for installation

KIT CONTENTS

Figure 1. Kit Contents: Security Anchor Kit

NOTE

Verify all contents are present in the kit before installing or removing items from vehicle.

Table 2. Kit Contents: Security Anchor Kit

Item	Qty	Description	Part No.
1	1	Floor anchor	Not sold separately
2	4	Expanding shield nut	Not sold separately
3	4	Ball bearing, 3 mm	Not sold separately
4	1	Drill bit, masonry	Not sold separately
5	2	Screw, phillips head bolts	Not sold separately
6	1	Wrench, hex socket	Not sold separately

NOTE

Verify all contents are present in the kit before installing or removing items from vehicle.

GENERAL

Security anchor can be installed on concrete ground or mounted on a concrete wall. Do not mount to hollow soft, porous concrete building block or house brick as these are not strong enough.

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

Kit can be installed on truck bed/trailer with separate purchase of Security Anchor Installation Kit (12600354).

This kit is not intended to be used as a tie-down. Anchor is only intended to serve as a loop point for a lock.

INSTALL

NOTE

Choose an area free of any cracks or chips in concrete. Test desired area of installation. With a hammer, lightly tap surface, listen for a solid sound. If hollow sound is heard, move and test a different area for installation.

1.	Figure 5 Remove cover (4) by placing a flat head screw driver under slot slowly (on both sides) until it pops out.
2.	Outline baseplate (3) and center point of one hole with felt marker on desired location.
3.	Figure 2 Measure and mark drill bit (1) 77 mm (3 in).
4.	Figure 2 Drill hole straight and vertical into concrete to depth marked on drill bit. NOTE Vacuum all dust and debris in and around holes drilled.
5.	Figure 2 Install expanding shield nuts (5) into concrete. a. Tap lightly until flush with top of concrete.
6.	Figure 3 Place baseplate (2) over outlined mark made earlier.
7.	Figure 3 Install hex head bolt (1). Turn until it catches expanding shield nut (3).
8.	Figure 3 Align baseplate (2) and mark center point for next hole with a felt marker.
9.	Figure 3 Remove hex head bolt (1) and baseplate (2).
10.	Repeat steps (4-9 ) until all four holes have been drilled.
11.	Figure 3 Align baseplate (1) and place all four hex head bolts (1).
12.	Tighten bolts with 6 mm Allen wrench evenly in a clockwise rotation. Do not over tighten. NOTE This is the anti-theft part that will stop someone from undoing base plate from concrete floor. For extra security, add epoxy to cover area.
13.	Figure 4 Install security ball bearing (1) into top of hex head bolt cavity. a. With hammer, tap expanding shield nuts (3) as far as it will go.
14.	Repeat step (13) for remaining three bolts.
15.	Figure 5 Install cover (2) over U-bolt on baseplate (3).
16.	Figure 5 Install bolts (1). Tighten until snug.
17.	Figure 5 Install cover (4) and plugs into open holes. a. Push plugs in with even thumb pressure.

1	Drill bit
2	Drill bit mark, 77 mm (3")
3	Concrete
4	Drill depth, 77 mm (3")
5	Expanding shield nut (4)

Figure 2. Drilling

1	Bolt (4)
2	Baseplate, security anchor
3	Expanding shield nut (4)

Figure 3. Security Anchor Installation

1	Security ball bearing (4)
2	Bolt (4)
3	Expanding shield nut (4)

Figure 4. Hardened Security Ball Bearing

1	Bolt, phillips head (2)
2	Cover, security
3	U-bolt/baseplate
4	Cover, logo

Figure 5. Security Anchor Installation