PASSENGER PILLIONS
941002822023-09-15
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
52400288, 52400306 | Safety Glasses, Torque Wrench |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Passenger Pillion
Table 2. Kit Contents: Passenger Pillion Kit
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Passenger pillion | 52400260 | |
| Sundowner solo pillion | Not sold separately | |||
| 2 | 2 | Screw | 2952A | |
| 3 | 2 | Nut kit assembly | 59768-97 | |
| 4 | 6 | Protective tape | 11100176 | |
| 5 | 1 | Cable strap | 10039 | |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGDo not install these seat kits on motorcycles that are not equipped with an appropriate grab strap and passenger footpegs. If footpegs and grab strap are not installed, passenger could fall from moving motorcycle or grab onto operator, causing loss of control and death or serious injury. (00410b)
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
REMOVE
NOTE
When performing the following installation procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs.
| 1. | Lift rider seat to gain access to pillion front mount location. | |
| 2. | Figure 3 Remove rear fender plug (1). |
INSTALL
| 1. | Figure 2 Install rear mount fender nuts (1) and washers (2). a. Cable strap (3) used to aid installation of nut and washer through bottom of fender. b. With rib on fender nut (1) seated into notch in fender hole, slide washer (2) into place. c. Remove cable strap (3). | |
| 2. | Figure 4 Mark and apply protective tape (2). a. Mark bottom of pillion isolators (1) with chalk. b. Set pillion in place and press down to transfer marks to fender. c. Place protective tape (2) on rear fender over marks. | |
| 3. | Figure 3 and Figure 5. Install pillion. a. Engage front mount tab (3). b. Secure with screws (1). Tighten. Torque: 2.3–4.6 N·m (20–41 in-lbs) | |
| 4. | Install seat. After installing seat, pull up on seat to verify that it is secure. See service manual. |
| 1 | Fender nut |
| 2 | Washer |
| 3 | Cable strap |
Figure 2. Install Fender nuts
| 1 | Rear fender plug |
| 2 | Front mount location |
| 3 | Fender nut locations |
Figure 3. Remove Fender Rear Plug
| 1 | Pillion isolator (6) |
| 2 | Protective tape (6) |
Figure 4. Protective Tape
| 1 | Screw (2) |
| 2 | Seat |
| 3 | Front mount tab |
Figure 5. Install Passenger Pillion