HAND GRIPS
941000292023-10-20
GENERAL INFORMATION
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
56100402, 56100445, 56100446, 56100448, 56100449, 56100462, 56100477
Safety Glasses, Torque Wrench
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Hand Grips (Typical)
Table 2. Kit Contents: Hand Grips
Verify that all contents are present in the kit before installing or removing items from vehicle.
Item
Qty
Description
Part No.
Notes
1
1
Grip, left, Kit 56100402, black
56100406
Grip, left, Kit 56100448, black and orange
56100452
Grip, left, Kit 56100449, gray
56100453
Grip, left, Kit 56100462, black
56100461
Grip, left, Kit 56100477, black
56100493
Grip, left, Kit 56100445, edge cut
56100441
Grip, left, Kit 56100446, black
56100440
2
1
Grip, right, Kit 56100402, black
56100405
Grip, right, Kit 56100448, black and orange
56100450
Grip, right, Kit 56100449, gray
56100451
Grip, right, Kit 56100462, black
56100460
Grip, right, Kit 56100477, black
56100494
Grip, right, Kit 56100445, edge cut
56100444
Grip, right, Kit 56100446, black
56100443
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
Kit 56100462: End cap (p/n 55801095) quantity of (2) is required
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
REMOVE
Left
1. See Figure 2. Remove end cap (1).
2. Remove hand grip (2).
a. Loosen clamp screw (3).
b. Remove grip.
Right
1. Remove end cap (1).
2. See Figure 3. Remove rear cover (3).
3. Remove grip. See service manual.
INSTALL
NOTE
When routing and closing Right and Left Hand Control Modules (R&LHCMs), verify there are no pinched wires. See service manual.
Left
NOTE
Kit 56100462, use end caps (p/n 55801095).
1. See Figure 2. Install hand grip.
a. Place grip (2) in position.
b. Tighten clamp screw (3).
Torque: 4.4–4.8 N·m (39–42 in-lbs)
2. Install end cap (1). Tighten.
Torque: 14–20 N·m (124–177 in-lbs)
Right
1. See Figure 4. Install hand grip. See service manual.
a. Align Twist Grip Sensor (TGS) tabs (2) with gaps in grip (1).
b. Place grip in position.
NOTE
When installing Right Hand Control Module (RHCM), verify throttle end play is set correctly. See service manual.
2. See Figure 3. Place rear cover (3) in position.
3. Tighten screws (2).
Torque: 0.6–0.9 N·m (5–8 in-lbs)
4. See Figure 3. Install end cap (1). Tighten.
Torque: 14–20 N·m (124–177 in-lbs)
NOTE
Check for free throttle movement.
1End cap
2Grip
3Clamp screw
Figure 2. Left Side Grip (typical)
1End cap
2Screw (2)
3Rear cover
Figure 3. Front Cover (left side shown)
1Grip
2TGS tab (2)
Figure 4. TGS Engagement