OFF ROAD ADJUSTABLE REAR BRAKE LEVER
941003262023-01-17
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
41600371 | Safety Glasses, Torque Wrench |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Off Road Adjustable Brake Lever
Table 2. Kit Contents: Off Road Adjustable Brake Lever
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Mounting bracket | Not sold separately | |
| 2 | 2 | Bushing | 11000330 | |
| 3 | 1 | Snap ring | Not sold separately | |
| 4 | 1 | Adjusting pin | Not sold separately | |
| 5 | 1 | Spring | Not sold separately | |
| 6 | 1 | Lever, rear brake, adjustable | Not sold separately | |
| 7 | 1 | Clevis pin | 12000110 | |
| 8 | 1 | Clevis, foot pedal | 33600410 | |
| 9 | 1 | Screw, flat head, TORX | 10201354 | |
| 10 | 1 | Foot pedal | 50600553 | |
| 11 | 1 | Clip | 12200266 | |
| 12 | 1 | Knob | Not sold separately | |
| 13 | 1 | Screw | 10201352 | |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
REMOVE
| 1. | Figure 2 Remove and discard cotter pin (3). | |
| 2. | Remove clevis pin (1). | |
| 3. | Remove screw (8), washer (7) and nut (4). a. Discard screw (8) and washer (7). | |
| 4. | Remove OE brake lever (6). |
INSTALL
| 1. | Figure 3 Remove protective thread cover from screw (7). | |
| 2. | Install nut (4) and adjustable brake lever (6) with screw as an assembly. | |
| 3. | Tighten screw (7). Torque: 17–21 N·m (13–15 ft-lbs) | |
| 4. | Align master cylinder (2) with adjustable brake lever (6). | |
| 5. | Install clevis pin (1). | |
| 6. | Install new cotter pin (3). |
Adjustment
| 1. | Figure 3 Pull spring clevis (8) out. | |
| 2. | Adjust lever arm. | |
| 3. | Align spring clevis (8) with detent and lock into place. |
| 1 | Clevis pin |
| 2 | Master cylinder |
| 3 | Cotter pin |
| 4 | Nut |
| 5 | Bracket |
| 6 | OE Brake lever |
| 7 | Washer |
| 8 | Screw |
Figure 2. OE Brake Lever
| 1 | Clevis pin |
| 2 | Master cylinder |
| 3 | Cotter pin |
| 4 | Nut |
| 5 | Bracket |
| 6 | Adjustable brake lever |
| 7 | Screw |
| 8 | Spring clevis |
Figure 3. Adjustable Brake Lever