SCREAMIN EAGLE OHLINS SIDE COVER KIT
941004572023-06-07
GENERAL INFORMATION
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
54000321
Safety Glasses, Torque Wrench
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Screamin Eagle Ohlins Side Cover Kit
Table 2. Kit Contents: Screamin Eagle Ohlins Side Cover Kit
Verify that all contents are present in the kit before installing or removing items from vehicle.
Item
Qty
Description
Part No.
Notes
1
1
Side cover
61300783
2
1
Washer
6110
3
1
Screw
942
4
1
Bracket, pre-load adjuster
41600213
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
PREPARE
NOTICE
This device is sensitive to electrostatic discharge (ESD). To prevent damage to the device, always touch the motorcycle frame or a grounded surface before handling. (00588c)
1. Remove seat. See service manual.
2. Disconnect negative battery cable. See service manual.
3. Remove and discard right side cover. See service manual.
REMOVE
1. See Figure 2. If equipped with ABS: Disconnect ABS connector (4).
2. Remove cable straps (3).
3. Remove side cover mounting stud (2). Save for later use.
4. Remove screw (1).
5. See Figure 3. Remove ABS module (3) with bracket.
6. Remove screws (2).
7. Remove and discard bracket (1).
1Screw
2Side cover mounting stud
3Cable strap (2)
4Connector
Figure 2. ABS Module with Bracket
ABS Bracket
Screw (2)
ABS Module
Figure 3. ABS Bracket
INSTALL
1. If equipped with ABS:
a. See Figure 4. Install new bracket (1) to ABS module.
b. Install screws (2). Tighten.
Torque: 10.8–13.5 N·m (96–119 in-lbs)
c. Install ABS module (3) with bracket.
d. See Figure 5. Install screw (1). Tighten.
Torque: 10.8–13.5 N·m (96–119 in-lbs)
e. Install side cover mounting stud (2). Tighten.
Torque: 8.1–10.8 N·m (72–96 in-lbs)
f. Install cable straps (3).
g. Connect ABS connector (4).
2. If equipped without ABS:
a. See Figure 6. Install new bracket (3).
b. Install screw (1). Tighten.
Torque: 10.8–13.5 N·m (96–119 in-lbs)
c. Install side cover mounting stud (2). Tighten.
Torque: 8.1–10.8 N·m (72–96 in-lbs)
1Pre-load adjuster bracket
2Screw (2)
3ABS Module
Figure 4. Bracket WITH ABS Module
1Screw
2Side cover mounting stud
3Cable strap (2)
4Connector
Figure 5. ABS Module
1Screw
2Side cover mounting stud
3Pre-load adjuster bracket
Figure 6. Bracket WITHOUT ABS Module
COMPLETE
1. If installing Screamin Eagle Ohlins Rear Suspension kit, do so at this time.
2. See Figure 1. Install new side cover (1).
3. Connect negative battery cable. See service manual.
4. Install seat. See service manual.