PASSENGER FOOT PEG KIT
J065282024-01-24
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
50500831, 50500832, 50500833, 50501830, 50501831, 50501832, 50502247, 50502248, 50502469, 50502470 | Safety Glasses, Torque Wrench |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Passenger Footpeg
Table 2. Kit Contents: Passenger Footpeg Kit
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Footpeg insert (black) | Not sold separately | |
| 2 | 1 | Medallion (2) | 14100879 | |
| 3 | 1 | Foot peg base (chrome) | Not sold separately | |
| 4 | 1 | Footpeg mount (chrome) | Not sold separately | |
Figure 2. Kit Contents: Passenger Footpeg
Table 3. Kit Contents: Passenger Footpeg Kit
| Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
| 1 | 1 | Footpeg, passenger, left (chrome) | 50501822 | |
| Footpeg, passenger, left (black) | 50501823 | |||
| 50502508 | ||||
| Footpeg, passenger, left (black edge cut) | 50501824 | |||
| Footpeg, passenger, left (black adversary) | 50502395 | |||
| Footpeg, passenger, left (grey adversary) | 50502397 | |||
| Footpeg, passenger, left (silver) | 50502509 | |||
| 2 | 1 | Footpeg, passenger, right (chrome) | 50501825 | |
| Footpeg, passenger, right (black) | 50501826 | |||
| 50502508 | ||||
| Footpeg, passenger, right (black edge cut) | 50501827 | |||
| Footpeg, passenger, right (black adversary) | 50502394 | |||
| Footpeg, passenger, right (grey adversary) | 50502396 | |||
| Footpeg, passenger, right (silver) | 50502509 | |||
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
INSTALL
NOTE
See Figure 3. When performing the next step, verify that spring (7) is positioned inside of footpeg (3).
| 1. | See Figure 3. Vehicle has a pin (2) and E-clip (1). Remove them and retain for future use. Save all hardware, including detent spring (7), detent ball (6) and detent plate (5) for installation of the new footpegs (3). | |||||||||||||||
| 2. | Insert detent spring (7) into new footpeg (3), followed by detent ball (6). | |||||||||||||||
| 3. | Position detent plate (5) on footpeg clevis edge while capturing detent ball (6) and detent spring (7) inside detent plate (5) while sliding detent plate (5) onto footpeg clevis. | |||||||||||||||
| 4. | Align detent plate (5) and footpeg (3) with footpeg mount on vehicle. | |||||||||||||||
| 5. | Install pin (2) and E-clip (1). | |||||||||||||||
| WARNING Footrests must fold up and toward rear of motorcycle if struck. Failure to set footrests to fold up and back could result in death or serious injury. (00366a) | ||||||||||||||||
| 6. | Defiance and Performance Passenger Pegs (only) - adjust orientation as follows: a. Rotate to desired orientation. b. Fold peg up to stowed position and confirm clearance to other components. Adjust as necessary. c. Tighten adjustment screw. Torque: 28.5 N·m (21 ft-lbs) | 
Figure 3. Footpeg Assembly |