DETACHABLE CONVERSION HARDWARE
941005222024-01-23
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
54000337 | Safety Glasses, Torque Wrench, Loctite (red) |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Detachable Conversion Hardware
Table 2. Kit Contents: Detachable Conversion Hardware Kit
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 2 | Screw, flat, TORX, 5/16-18X2, black | Not sold separately | |
| 2 | 2 | Screw, buttonhead, TORX, 5/16-18X2 | Not sold separately | |
| 3 | 4 | Spacer | Not sold separately | |
| 4 | 2 | Tape, protective, upright | Not sold separately | |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
Separate purchase of Docking Hardware kit (Part No. 52300353 or 52300354) is required for installation of this kit.
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
PREPARE
| 1. | Remove saddlebags. See service manual. |
REMOVE
| 1. | Figure 2 Remove screws (1). Discard. | |
| 2. | Remove Original Equipment (OE) remote reservoir bracket (2). a. Do not remove or loosen any of the remote reservoir hoses or bolts. | |
| 3. | Repeat steps for opposite side of vehicle. |
| 1 | Screw (2) |
| 2 | Remote reservoir bracket |
Figure 2. Remove Remote Reservoir Bracket
INSTALL
| 1. | Install docking hardware kit (Part No. 52300353 or 52300354). Follow instructions included in that kit. a. Discard mounting washers (Part No. 6302) and screws (Part No. 10200157). | |
| 2. | Figure 3 Install spacers (5). | |
| 3. | Apply threadlocker to threads of screws (3,4). LOCTITE 262 HIGH STRENGTH THREADLOCKER AND SEALANT (RED) (94759-99) | |
| 4. | Install OE remote reservoir bracket (2) to outside of fender support and screws (3,4). | |
| 5. | Tightens screws (3,4). Torque: 27.1 N·m (20 ft-lbs) | |
| 6. | Repeat steps for opposite side of vehicle. |
NOTE
If installing an upright or detachable rack to vehicle, check if there is any contact between rubber sheath on remote reservoir hose and upright bar. If contact exists, place protective tape (4, Figure 1 ), on both sides of upright bar for protection.
| 1 | Docking hardware kit |
| 2 | Remote reservoir bracket |
| 3 | Screw, buttonhead |
| 4 | Screw, flathead |
| 5 | Spacer (2) |
Figure 3.
COMPLETE
| 1. | Install saddlebags. See service manual. | |
| 2. | When saddlebag lids are open, check that no contact exists between reservoir, hoses and lid. |