HEATED SEAT KIT
941005672024-07-02
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
52000668, 52000812 | Safety Glasses, Torque Wrench |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Heated Seat
Table 2. Kit Contents: Heated Seat Kit
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Screw | 10200004 | |
| 2 | 1 | Seat | Not sold separately | |
| 3 | 1 | Grab strap | 52400335 | Kit 52000668 |
| 52400350 | Kit 52000812 | |||
| 4 | 1 | Service kit, switch cap replacement (not shown) | 99800062 | Not included in seat kit |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGDo not install these seat kits on motorcycles that are not equipped with an appropriate grab strap and passenger footpegs. If footpegs and grab strap are not installed, passenger could fall from moving motorcycle or grab onto operator, causing loss of control and death or serious injury. (00410b)
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
Electrical Overload
NOTICE
It is possible to overload the vehicle's charging system by adding too many electrical accessories. If the combined electrical accessories operating at any one time consume more electrical current than the vehicle's charging system can produce, the electrical consumption can discharge the battery and cause damage to the vehicle's electrical system. (00211d)
WARNINGWhen installing any electrical accessory, be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modified. Exceeding the maximum amperage can lead to electrical failures, which could result in death or serious injury. (00310a)
The Heated Seat requires up to 4.2 Amps of current from the electrical system.
NOTE
Customers with limited sensitivity to hot or cold should not use this product.
PREPARE
| 1. | Remove saddlebag. See service manual. | |
| 2. | Remove main fuse. See service manual. | |
| 3. | Remove Original Equipment (OE) seat and grab strap. See service manual. |
INSTALL
| 1. | See Figure 2. Install new grab strap. a. Install grab strap (2) to studs (1). b. Install custom screws (3). Torque: 0.9–1.7 N·m (8–15 in-lbs) Thumb nuts Torque: 7–11 N·m (62–97 in-lbs) Flange nuts c. Models with side plate grab may remove side plate. | |
| 2. | Locate seat harness connector on underside of seat. | |
| 3. | See Figure 2. Connect seat connector to P&A accessory connector (4). NOTE If another accessory is connected, separate purchase of Jumper (Part no. 69203476) may be required. | |
| 4. | Route wiring beneath seat. a. Make sure wiring will not get pinched when seat is installed. b. Verify harness fuse holder cap is fully seated and secured. | |
| 5. | See Figure 2. Insert rear of seat through grab strap (2) until seat mounting slot (1, Figure 3 ) on front underside of seat is behind seat tongue (5). | |
| 6. | See Figure 2. Slide seat forward until seat tongue fully engages into seat mounting slot (5). | |
| 7. | See Figure 1. Install seat screw (2). Tighten. Torque: 5.4–8.1 N·m (4–6 ft-lbs) | |
| 8. | Install seat. After installing seat, pull up on the seat to verify that it is secure. See service manual. |
| 1 | Stud (2) |
| 2 | Grab strap |
| 3 | Custom screw (2) |
| 4 | P&A Connector [4] |
| 5 | Seat tongue |
Figure 2. Component Locations
| 1 | Seat slot |
Figure 3. Seat Mount Slot
OPERATION
NOTE
- Seat operation while vehicle's engine is turned off or running below normal operating speed can quickly discharge vehicle battery. This could lead to a subsequent failure to start and could damage the electrical system.
- For some vehicles, accessory switch is a rocker switch found on inner fairing switch panel. With ignition/key switch at IGNITION or ACCY, close circuit to heated seat by flipping accessory switch from OFF to ON.
- See owner's manual for operation of vehicle's accessory circuit.
Seat Control Switches
| 1. | See Figure 4. Switches (1, 2): a. Controls individual level setting of rider and passenger zones. b. Controls are independent. c. Detents on switches allow operator to quickly return to preferred setting. d. Rider control (1) is located closest to rider's seating position. e. Passenger control (2) is located closest to passenger's seating position. f. For rider and passenger control switches, there are three total positions. Downward setting is low power, upward setting is maximum power and middle setting turns off rider or passenger control independently. |
NOTE
- Heated seat will remain on without rider or passenger intervention for one hour, at which point it will automatically shut off. Toggle power switches to turn back on.
- If switchcaps become damaged, Switch Cap Replacement service kit (Part No. 99800062) is available and can be purchased separately.
| 1 | Heat control, rider |
| 2 | Heat control, passenger |
Figure 4. Seat Heating Control Switches