PRIMARY AUDIO AMPLIFIER KIT (PN 76001294)

941003622024-05-31

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
76001294	Safety Glasses, Torque Wrench

(1) Tightening to torque value or other moderate tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Audio Amplifier Kit

Table 2. Kit Contents: Audio Amplifier Kit

	Verify that all contents are present in the kit before installing or removing items from vehicle.
	Item	Qty	Description	Part No.	Notes
	1	1	Amplifier, primary audio	Not sold separately

GENERAL

Instruction sheet is also available electronically. To verify you are using the most current version available, do one of the following:

Go to h-d.com/isheets
Scan QR code in upper left corner of the instruction sheet

NOTE

This instruction sheet may have a Supplemental Video to assist installer in clarifying a certain part of the assembly. A linked video would be located at the end of this instruction sheet.

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

WARNING

Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)

NOTE

This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:

A Harley-Davidson dealer.
H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.

This item is available at a Harley-Davidson dealership:

NOTE

Damage WILL occur to OE speakers when this audio amplifier is installed.

2024-later FLHX and FLTRX: Separate purchase of Speaker Kits (Part No's 76001295, 76001296, 76001297 or 76001298) is required for this installation.

Installation by a technician at a Harley-Davidson dealership is recommended.

To ensure proper audio performance, speaker set up in the Infotainment Control Unit (IFCU) OR Digital Technician II (DT II) is required for audio configuration and amplifier firmware update.

See the Harley-Davidson website and select Software Updates. The link will open up the Infotainment Support Resources for software updates.

PREPARE

1.	Remove left saddlebag. See service manual.
2.	Remove left side cover. See service manual.
3.	Remove main fuse. See service manual.
4.	Remove outer fairing. See service manual.

REMOVE

See Figure 2. Remove Original Equipment (OE) amplifier.

a. Remove screws (1).

b. Remove amplifier (3).

c. Disconnect connector (2).

INSTALL

NOTE

Damage WILL occur to OE speakers when this audio amplifier is installed. Refer to Installation Requirements.

1.	See Figure 2. Install amplifier.
2.	Connect connector (2).
3.	Install amplifier (3) on mounts.
4.	Install screws (1). Tighten. Torque: 5.5–6.8 N·m (49–60 in-lbs)

1	Screw (4)
2	Connector
3	Amplifier

Figure 2. Amplifier

COMPLETE

NOTE

To prevent possible damage to the sound system, verify that the ignition is OFF before installing the main fuse.

1.	Install outer fairing. See service manual.
2.	Install main fuse. See service manual.
3.	Install left side cover. See service manual.
4.	Install left saddlebag. See service manual.

CONFIGURE

NOTE

Update software in this order:

Step 1. Update Infotainment Control Unit (IFCU) software to the latest version.
Step 2. Update amplifier software to the latest version.

Do not proceed without performing these updates.

1.	From the www.harley-davidson.com website. a. Select: Software Updates. This links to Infotainment Support Resources. b. Select: Infotainment Control Unit (IFCU) Skyline^TM OS Located in Table of Content. c. Follow the instructions to transfer the update to the (IFCU) and Amplifiers as equipped.
2.	Perform system configuration ONLY after all audio accessory kits have been installed.
3.	Power up vehicle in accessory mode.
4.	On the Infotainment Control Unit (IFCU): a. Select: Settings icon. b. Select: Sounds Settings. c. Follow on screen prompts for applicable audio system changes.
5.	When complete, turn power off for 60 seconds.
6.	Turn the ignition ON, but do not start the vehicle.
7.	Make sure that all speakers are working properly. Check that front and rear fader function is operating correctly. If not, check speaker wiring. Refer to Installation Requirements.