STAGE I & II SPEAKER KIT - FRAME MOUNTED FAIRING (PN 76000982 and 76000983)

941001582021-02-04

QUAKE

GENERAL

NOTE

The QR code can only be scanned in the Harley-Davidson audio app.

The newly installed audio system and speakers will not play audio unless it is configured using the Harley-Davidson audio app or by an authorized Harley-Davidson dealership.

Table 1.

Harley-Davidson Audio Powered by Rockford Fosgate®
Kit	QR Code
76000982 (Stage I)
76000983 (Stage II)

NOTE

The various generations of speakers, amplifiers and wiring for Harley-Davidson vehicles were not designed or tested to work together. Please refer to the P&A catalog for fitment recommendations and consult your dealership to ensure optimal performance and compatibility.

The Harley-Davidson Audio Powered by Rockford Fosgate speakers are acoustically optimized to work together with speakers of the same stage level (I or II). The speaker’s output signals are assigned by the APP including location and stage level. If speaker output assignments, stage numbers and locations, are incorrectly configured, damage will not occur, but diminished performance should be expected.

Models

NOTE

These speakers are for use ONLY on 2014 and later Harley-Davidson audio systems. Using these speakers on 2006-2013 Harley-Davidson audio systems WILL permanently damage these speakers. Using these speakers on 2005 or earlier Harley-Davidson audio systems WILL permanently damage those systems.

For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).

Ensure you are using the most current version of the instruction sheet which is available at: h-d.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

Download Harley-Davidson mobile app.

These items are available at your Harley-Davidson dealership.

2014 and Later FLTRUSE and Touring: Separate purchase of Harley-Davidson Primary Amplifier and Dongle Kit (Part No. 76000997) is required for this installation.
2014 and Later FLTRUSE and Touring: Separate purchase of Harley-Davidson Primary Amplifier Installation Kit (Part No. 76000974 or 76001045) is required for this installation.
2014 and Later FLTRUSE and Touring: Separate purchase of Harley-Davidson Secondary Amplifier Installation Kit (Part No. 76000975) may be required for this installation. This depends if there are six or more speakers and how the amplifier channels are assigned.
2014 and Later Touring: Separate purchase of Harley-Davidson Fairing Speaker Harness Install Kit (Part No. 76000992) may be required for this installation.
2015 and Later FLTRUSE: Separate purchase of Harley-Davidson Fairing Speaker Harness Install Kit (Part No. 76001100) may be required for this installation.

WARNING

Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)

Installation by a technician at a Harley-Davidson dealership is recommended.

Kit Contents

See Figure 11 and Table 2

PREPARE

WARNING

To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)

NOTE

This instruction sheet references service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.

1.	Remove left saddlebag.
2.	Remove left side cover.
3.	NOTE Models with security: Disable security system. Remove main fuse.
4.	Remove OEM speaker grilles and discard.

REMOVE

1.	Figure 3 Remove screws (1) and discard.
2.	Gain access to speaker connectors (2) and disconnect.
3.	Remove OEM speaker (3) from enclosure.
4.	Repeat steps 1-3 for opposite side.

1	Screw (4)
2	Speaker connectors
3	OEM Speaker

Figure 3. Speaker Enclosure Removal (Left Side Shown)

INSTALL

NOTE

Figure 11 The new speaker grilles are side-specific. The Bar and Shield logos are oriented toward the inboard.

Verify proper orientation of the Bar & Shield emblem before proceeding.

1.	Figure 11 Install speaker (2, 5 or 3, 4) into enclosure. a. Figure 5 Orient speaker to enclosure. b. Figure 4 Connect speaker connectors (5). NOTE Different size spade contacts prevent improper assembly. c. Install speaker (3) to enclosure using alignment pin (4). d. Install screws (2). Tighten. Torque: 1–1.5 N·m (9–13 in-lbs)
2.	Install speaker grille (1) using tabs (6, 7).
3.	Repeat steps 1-2 for opposite side.

1	Speaker grille (Stage 1 or 2)
2	Screw (4)
3	Speaker (Stage 1 or 2)
4	Alignment pin
5	Speaker connectors
6	Inner tab (2)
7	Outer tab

Figure 4. Speaker Enclosure Installation (Left Side Shown)

1	Left stage 1 speaker
2	Left stage 2 speaker
3	Left and right speaker enclosures
4	Right stage 2 speaker
5	Right stage 1 speaker

Figure 5. Speaker Orientation (Typical)

COMPLETE

NOTE

To prevent possible damage to the sound system, verify that the ignition is OFF before installing the main fuse.

1.	Install main fuse.
2.	Turn the ignition ON, but do not start the motorcycle.
3.	Make sure that all speakers are working and front/rear fader function is operating correctly. If not, check speaker wiring.
4.	Install left side cover.
5.	Install left saddlebag.

APP SETUP

Unresolved graphic link Accessing your audio system.

a. Pair device (1) to system.

b. Access app menus (2) to setup vehicle sound system.

1	Add bluetooth device
2	Configure audio system

Figure 6. System Access

Unresolved graphic link Main menu screen.

a. Main menu icon (1).

b. Reset or change security personal identification number (PIN) (2).

c. Edit and rename your system (3).

d. Customize main menu with your bike picture (4).

e. Bluetooth connection indicator. Slash through symbol indicates: Not Connected (5).

1	Main menu
2	Change security pin
3	Rename system
4	Customize main menu picture
5	Bluetooth connection indicator

Figure 7. Main Menu

Unresolved graphic link Setup menu screen.

a. Setup menu icon (1).

b. Use to scan QR code (2) on iSheet.

c. Manual setup for Stage 1 or 2 speakers, speaker location and white noise to assign speaker locations.

1	Setup menu
2	QR Code scan
3	Manual setup

Figure 8. Setup Menu

Unresolved graphic link Equalizer setup screen.

a. Equalizer setup icon (1)

b. Tune 7-Band equalizer (2) frequencies.

c. Custom or preset equalizer selections (3).

1	Equalizer menu
2	7-Band equalizer
3	Equalizer preset selection

Figure 9. Equalizer Menu

Unresolved graphic link Diagnostic menu screen.

a. Diagnostic menu icon (1) displays sound system status.

b. Open the speaker testing screen (2).

c. Refreshes speaker and amplifier status (3) after component repair.

d. Select speaker for white noise (4) test and functionality.

e. Return to diagnostic menu screen (5).

1	Diagnostic menu
2	Speaker test screen
3	Refresh status
4	Select a speaker to play white noise
5	Finish and return to diagnostic menu

Figure 10. Diagnostic Menu

SERVICE PARTS

Figure 11. Service Parts, Boom! Audio 6.5 in Front Fairing Speaker Kit

Table 2. Service Parts

Item	Description (Quantity)	Part Number	Kit Number
1	Speaker grille, left, stage 1	76001020	76000982
1	Speaker grille, left, stage 2	76001022	76000983
2	Speaker, left, stage 1	76000998	76000982
3	Speaker, left, stage 2	76000999	76000983
4	Speaker, right, stage 2	76001011	76000983
5	Speaker, right, stage 1	76001010	76000982
6	Speaker grille, right, stage 1	76001021	76000982
6	Speaker grille, right, stage 2	76001023	76000983
7	Screw, self-tapping, button head (8)	10201096	76000982, 76000983