FLST (WITH FOG/PASSING LAMPS) DETACHABLE WINDSHIELD KIT
J053802017-08-22
GENERAL
Kit Number
57400110, 57400111, 57400112, 57400113, 57400114, 57400115
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Additional Parts Required
NOTE
A service manual for your model motorcycle is available from a Harley-Davidson Dealer.
INSTALLATION
WARNINGRider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
NOTE
Place shop rags on the headlamp and front of the fuel tank to prevent scratches to headlamp and fuel tank Be sure the windshield assembly does not contact chrome or painted parts. Contact will cause scratches to chrome or painted parts.
Spacers on the topmost screws will fall free when the screws are removed. Take care that the spacers do not strike the fuel tank or fender, damaging the finish.
| 1. | Remove the stock windshield, if so equipped. Discard the windshield. NOTE Keep front wheel straight to prevent brackets from scratching fuel tank. | |
| 2. | Figure 2 and Table 2. Remove and discard the original bottom fog/passing lamp bracket screw (4) and washer (1). | |
| 3. | Place a new flat washer (1), bushing (2) and flat washer (1) on a 1-3/8 inch long screw (4) from the kit. Thread the screw through the lower hole in the fog/ passing lamp bracket and decorative fork cover, and into the triple clamp. Tighten. Torque: 10.8 N·m (8 ft-lbs) screw | |
| 4. | Repeat Step 3 on the opposite side of the motorcycle. | |
| 5. | Place a flat washer (1), bushing (2), and flat washer (1), on a screw (3) from the kit. Place the screw through the top hole of the fog/passing lamp bracket and through OE spacer. Tighten. Torque: 10.8 N·m (8 ft-lbs) screw | |
| 6. | Repeat Step 5 on the opposite side of the vehicle. |
WARNINGImproper installation of accessories or loading of cargo can affect motorcycle stability and handling, which could result in death or serious injury. (00455b)
WARNINGFailure to provide adequate clearance between stationary and moving parts can cause loss of control, which could result in death or serious injury. (00378a)
NOTE
Inspect windshield upon completion of installation. Be sure windshield mounting does not restrict full left or full right movement of front fork assembly. If restriction does occur, adjust windshield as needed until proper clearance is obtained. Have experienced Harley-Davidson service personnel correct any problems before riding with this accessory installed.
NOTE
Check mounting hardware periodically. Never ride with loose mounts. A loose mounting causes extra stress on all other mounts, as well as the windshield itself, and could result in premature failure of components.
REMOVING THE WINDSHIELD
To remove the windshield, grab the windshield edges on each side of the center brace and firmly pull the windshield loose from the bushing grooves.
CARE AND CLEANING
NOTE
Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections.
NOTICE
Use only Harley-Davidson recommended products on Harley-Davidson windshields. Do not use harsh chemicals or rain sheeting products, which can cause windshield surface damage, such as dulling or hazing. (00231c)
Do not clean polycarbonate in hot sun or high temperature. Powdered, abrasive or alkaline cleanser will damage the windshield. Never scrape the windshield with a razor blade or other sharp instruments because permanent damage will result.
NOTE
Covering the windshield with a clean, wet cloth for about 15 minutes before washing will make dried bug removal easier.
Harley-Davidson Windshield Water Repellent Treatment Part Number 99841-01 is approved for use on Harley-Davidson windshields.
SERVICE PARTS
Figure 1. Service Parts: Windshield Kits
Table 1. Service Parts: Windshield Kits
Item | Description (Quantity) | Part Number | Item | Description (Quantity) | Part Number | |
|---|---|---|---|---|---|---|
1 | Windshield, standard height, clear | 58241-95 | 9 | Screw, button head (2) 1/4-20 x 1-1/4 inch | 94426-95 | |
Windshield, low, smoked | 58277-95 | 10 | Windshield retainer (right) | 58253-95 | ||
Windshield, standard height, clear | 58294-09 | 11 | Windshield retainer (left) | 58252-95 | ||
Windshield, 2 inch taller than standard, clear | 57754-04 | 12 | Nylon bushing (4) | 58272-95 | ||
2 | Screw, pan head, Torx (2 ) #12-24 x 13/16 inch | 2452 | 13 | Brace, vertical, right, polished | 58406-75A | |
3 | Screw, pan head, Torx (7) #12-24 x 5/8 inch | 2921A | Brace, vertical, right, black | 58045-09 | ||
4 | Brace, horizontal, inner, polished | 58431-94 | 14 | Brace, vertical, left, polished | 58408-75A | |
Brace, horizontal, inner, black | 57690-10 | Brace, vertical, left, black | 58046-09 | |||
5 | Brace, horizontal outer windshield, polished | 58428-94 | 15 | Tape, windshield bracket (2) | 58417-77 | |
Brace, horizontal outer windshield, black | 57689-10 | 16 | Flat washer, 1/4 inch, silver (2) | 6703 | ||
6 | Tape | 58416-77A | 17 | Acorn nut, #12-24 (chrome) (9) | 7651A | |
7 | Bracket, left, polished | 58291-95 | 18 | Acorn nut, 1/4-20 (chrome) (2) | 94004-90T | |
Bracket, left, black Bracket left chrome | 12700042 57063-00A | 19 | Hardware kit: Washer, heat treated (8) Hex socket button head screws (2) Hex socket button head screws (2) Bushing (4) | 91800025 | ||
8 | Bracket, right, polished Bracket, right black | 57062-00A 12700043 | ||||
Bracket, right, chrome | 57062-00A | NOTE: Appearance of actual components may vary from illustration. | ||||
Figure 2. Service Parts: Hardware Kit
Table 2. Service Parts Table
Item | Description (Quantity) | Part Number |
|---|---|---|
1 | Washer, 0.105 inch (2.7 mm) (8) | 6400HB |
2 | Bushing (4) | 67621-94 |
3 | Screw, button head, 1 3/4 inch | 4343 |
4 | Screw, button head, 1 3/8 inch | 4482 |
Items mentioned in text: | ||
A | Decorative triple clamp cover | |
B | Fog/Passing lamp bracket | |
C | Original equipment spacer | |