STREAMLINER PASSENGER FOOTBOARD KIT
J050442020-01-14
GENERAL
Kit Number
50378-07B, 50501819
Models
For model fitment information, see the P&A Retail Catalog or Parts and Accessories section of www.harley-davidson.com (English only).
WARNING
Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
Kit Contents
See Figure 2 and Table 1.
REMOVAL
  1. See Figure 1. Remove existing passenger footpegs or footboards, brackets and mounting hardware.
1Screw and washer
2Bracket
3Footpeg mount
4Footpeg pad and bottom
Figure 1. Passenger Footpeg Components (FLHX)
INSTALLATION
NOTE
  • If necessary, remove any paint from counterbore holes of footboard brackets to ease the installation of the pivot pins.
  • On 2010 and Later Models: The installation height can be adjusted to one of three positions. To install footboards in a new position, remove plastic plugs from holes in rear swingarm bracket as necessary.
  • On 2009 and Earlier Models: The lowest of the four holes on the frame is not threaded and cannot be used to mount the footboards.
1. See Figure 2. Insert shoulder bolt (9) or (10) through slot in footboard bracket (1). Tighten.
a. 2010 and Later Models: Thread the 5/16 inch shoulder bolt (9) into the lowest hole in the rear swingarm bracket of the frame.
b. 2009 and Earlier Models: Thread the 3/8 inch shoulder bolt (10) into the second lowest hole in the rear swingarm bracket of the frame.
2. At the desired height, install the upper screw (2) and lockwasher (3) through footboard bracket (1). Tighten.
Torque: 49–56 N·m (36–42 ft-lbs) footboard bracket
3. Install spring (4) into retaining hole in footboard bracket. Set the ball (5) on top of spring.
4. Position the detent in the bottom of the footboard pan (8 or 12) over ball in footboard bracket. Be sure not to unseat the ball. Press down on footboard pan so the holes of the footboard pan and footboard bracket align.
5. Insert pivot pins (7) through two mounting holes on footboard bracket and into footboard pan.
6. Align footboard insert (6 or 11) in footboard pan. Press insert firmly until the footboard pan tabs are firmly seated in the footboard insert.
7. Fold footboard up and install set screw (13) to secure footboard pad.
8. Pivot footboard assembly up and down to verify proper operation.
9. Repeat all steps for opposite side.
SERVICE PARTS
Figure 2. Service Parts: Streamliner Passenger Footboard
Table 1. Service Parts Table
Item
Description (Quantity)
Part Number
1
Footboard bracket (2)
53071-00A
Footboard bracket (2), Kit 50501819
52719-10
2
Screw, socket head cap (2)
94354-91T
3
Lockwasher (2)
94082-90T
4
Spring (2)
33085-74
5
Ball (2)
8861
6
Footboard insert, left
50422-05
Footboard insert, left, Kit 50501819
50501807
7
Pivot pin (4)
50933-86A
8
Footboard pan, left
50721-04
Footboard pan, left, Kit 50501819
50501810
9
Shoulder bolt, 5/16 inch (2)
4916
10
Shoulder bolt, 3/8 inch (2)
5005
11
Footboard insert, right
50421-05
Footboard insert, right, Kit 50501819
50501805
12
Footboard pan, right
50722-04
Footboard pan, right, Kit 50501819
50501811
13
Set screw (2)
3341