MINI-FOOTBOARD KIT
J047372018-08-21
GENERAL
Kit Numbers
50451-09, 50500109, 50500124, 50500139, 50500144, 50501148, 50501225
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
Softail models require separate purchase of footpeg support kit P/N 50454-09 when used in passenger position.
Kit Contents
  • For Kit 50451-09, see Figure 2. There are no service parts for this kit.
  • For all except Kit 50451-09, see Figure 3. Fasteners (4) 94334-91T (chrome) and 12600031 (black) are available service parts.
  • For Kit 50501148, see Figure 4 and Refer to Table 1.. Fastener (2) 10500147 (chrome) are available service parts.
  • For Kit 50501225, see Figure 4 and Refer to Table 1.. Fastener (2) 10500125 (black) are available service parts.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
WARNING
Footrests must fold up and toward rear of motorcycle if struck. Failure to set footrests to fold up and back could result in death or serious injury. (00366a)
INSTALLATION
1Spring washer
2Spring washer square edge
3Footpeg support slot
Figure 1. Footpeg Spring Washer Installation
1. Remove the locknuts and screws that hold the existing footpegs in place. If the motorcycle is equipped with a pin and retaining ring, remove them and retain for future use. Save all hardware for installation of the new footpegs.
2. Remove the existing footpegs and the spring washers. Save the spring washers for installation.
3. See footpeg support installation instructions for Softail models when used in passenger position.
NOTE
See Figure 1. When performing the next step, verify that the spring washer is positioned inside of the footpeg support with the square edge (2) towards the inside of the support.
4. Install the new footpegs in the same manner as the old footpegs were installed. Insert a spring washer (1) and the mount end of the footpeg inside the slots (3) of the footpeg supports.
5. Secure each footpeg and spring washer with the screw and locknut or pin and retaining ring removed earlier. Tighten.
Torque: 26 N·m (19 ft-lbs) Locknuts
NOTE
When rotating and adjusting the footboard for comfort, additional considerations should be made so that the footboard does not interfere with other components in the folded up position.
Verify that the footboard will fold up and back.
6. To adjust the footboard for comfort: 50451-09 kit, see Figure 2.
a. Remove the adjustment screw (4).
b. Partially remove the tread assembly (1, 2, 3) from the support shaft (5).
c. Rotate the tread assembly around the support shaft. Teeth on the shaft will engage the internal nut (3) every 10 degrees.
d. Fully seat the tread assembly back on the support shaft.
e. Install the adjustment screw. Tighten.
Torque: 29 N·m (21 ft-lbs) Adjusting screw
7. To adjust the footboard for comfort: all except 50451-09 kit, see Figure 3.
a. Remove the adjustment screw (4).
b. Partially remove the tread assembly (1 and 3) from the support shaft (2).
c. Rotate the tread assembly around the support shaft. Teeth on the shaft will engage teeth in the base every 10 degrees.
d. Fully seat the tread assembly back on the support shaft.
e. Install the adjustment screw. Tighten.
Torque: 29 N·m (21 ft-lbs) Adjusting screw
1Mini-Footboard, left
2Mini-Footboard, right
3Internal nut
4Adjustment screw
5Support shaft
Figure 2. Mini-Footboard Kit: 50451-09
1Tread
2Support Shaft
3Base
4Fastener
Figure 3. Mini-Footboard Kit: All Except 50451-09, 50501148, 50501225
1Tread
2Support Shaft
3Base
4Fastener
Figure 4. Mini-Footboard Kits: 50501148, 50501225
Table 1. Service Parts
Kit
Item
Description Quantity)
Part Number
50501148
Chrome
1
Tread, left side
50501181
Tread, right side
50501184
2
Shaft
50351-03
3
Base, left side
50501189
Base, right side
50501191
4
Screw, chrome
10500147
50501225
Black
1
Tread, left side
50501181
Tread, right side
50501184
2
Shaft
51428-09
3
Base, left side
50501190
Base, right side
50501192
4
Screw, black
10500125