RIDER FOOTBOARD - TOURING
941005502024-04-25
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
50502250A, 50502251A | Safety Glasses, Torque Wrench |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Rider Footboard Components
Table 2. Kit Contents: Rider Footboard Components
 | Item | Qty | Description | Part No. | Notes |
|---|---|---|---|---|---|
 | 1 | 1 | Footboard assembly, right side, gray | 50502323 | |
| 1 | Footboard assembly, right side, black | 50502322 | ||
| 2 | 1 | Footboard assembly, left side, gray | 50502325A | |
| 1 | Footboard assembly, left side, black | 50502324A | ||
| 3 | 4 | Screw | 10200986 | |
| 4 | 4 | Locking nut, flange | 7716 | |
| 5 | 2 | Wear peg | 50500628 | |
| 6 | 2 | Wear plate (not shown) | 50502575 | |
| 7 | 2 | Screw, wear plate (not shown) | 10200659 |
NOTE
Verify that all contents are present in the kit before installing or removing items from vehicle.
GENERAL
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Verify that the most current version of the instruction sheet is used. It is available at: www.harley-davidson.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
FLTRXSTSE models: Separate purchase of Front Support Mounts (Part No. 47200202A - qty of 2) is required. See service manual for removal of old front supports and install of new supports.
WARNINGRider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
REMOVE
| 1. | Remove two hinge bolts and locknuts attaching existing footboard to mounting brackets. | |
| 2. | Remove footboard. | |
| 3. | Vehicle hardware: |
INSTALL
| 1. | See Figure 1. Set correct footboard in place over mounting brackets. Wear peg should be toward rear of vehicle. | |
| 2. | Align holes, install pivot screws (1) and locking nuts (2). | |
| 3. | Locking nuts should be on inboard side. Tighten. Torque: 9–12 N·m (80–106 in-lbs) | |
| 4. | Check that footboard pivots freely on hinge bolts. a. If it does not, then loosen front footboard support bracket lower screw. Re-center in bracket in footboard groove. Tighten. Torque: 49–57 N·m (36–42 ft-lbs) | |
| 5. | Repeat for opposite side. |
Wear Peg Replacement
| 1. | When servicing wear peg, remove existing wear peg from footpeg. | |
| 2. | Apply two or three drops of threadlocker to threads of new wear peg.LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97) | |
| 3. | Install new wear peg to footpeg. Torque: 3.6–4.7 N·m (32–42 in-lbs) |