MID FRAME AIR DEFLECTORS
J043692007-01-08
GENERAL
Kit Number
58022-07
Models
For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Additional Parts Required
WARNINGRider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
INSTALLATION
| 1. | Refer to Owner's Manual and remove seat. | |||||||||||||||
| 2. | Remove stock plastic cruise control cable clip from frame near end of fuel tank if equipped. | |||||||||||||||
| 3. | See Figure 1. Assemble speed nuts (2) to both ends of mounting strap (1) and align edges of nuts to angled ends of strap. | 
Figure 1. Install Speed Nuts to Mounting Strap 
Figure 2. Mounting Strap Location 
Figure 3. Fastener Locations | ||||||||||||||
| 4. | See Figure 2. Install mounting strap assembly (1) through window of frame. Position strap so speed nuts are aligned over the 0.25 inch diameter holes in frame as shown. | |||||||||||||||
| 5. | See Figure 3. Attach strap assembly to frame using using a 0.750 inch length button head screw at location (1) and the 0.875 inch length button head screw at location (2) by inserting them from the underside of frame plate. Tighten screws enough to keep strap from moving. This locates the mounting strap and prevents it from shifting position during deflector installation. | |||||||||||||||
| 6. | Refer to the Figure 4 and Table 1 to obtain the necessary parts for the following steps. Refer to Figure 3 for location references. | |||||||||||||||
| 7. | Insert well nut (7) into underside of frame plate at location (3). Apply liquid soap to the outer surface of the well nut to ease installation | |||||||||||||||
| 8. | Remove screw from location (1) on right side of frame (as viewed from the top of the motorcycle looking forward). | |||||||||||||||
| 9. | Install right side deflector (6) using screw (9) and large washer (8) in location (1) and install screw (9) with small washer in location (3). Firmly push the deflector against the outer side of frame and tighten screws to 3.9–6.2 N·m (35–55 in-lbs). | |||||||||||||||
| 10. | Remove left side strap mounting screw. | |||||||||||||||
| 11. | Install cable clamp (5) to cruise control cable (if equipped). | |||||||||||||||
| 12. | Insert screw (11) through cable clamp, washer (8) and left side deflector (10) and install to mounting strap speed nut. Firmly push deflector against outside of rail and tighten screw to 3.9–6.2 N·m (35–55 in-lbs). | |||||||||||||||
| 13. | Install "U" clip (4) to deflector and frame plate at location (4). Clip barbs should be against frame plate. Reach into the frame window (from above the frame) to release the barbs from the plate during installation. | |||||||||||||||
| 14. | Insure that the cruise control cable is positioned above the rounded area of the "U" clip. | |||||||||||||||
| WARNING After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) | ||||||||||||||||
| 15. | Install seat. |
SERVICE PARTS
Figure 4. Service Parts: Mid Frame Air Deflectors Kit
Table 1. Service Parts Table
Item | Description (Quantity) | Part Number | Item | Description (Quantity) | Part Number | |
|---|---|---|---|---|---|---|
1 | Strap, mounting | Not Sold Separately | 7 | Well nut, 0.25-20 | 6596 | |
2 | Nut, speed 0.25-20 inch | 8108 | 8 | Washer, flat 0.25 inch (2) | 6036 | |
3 | Washer, flat, zinc plate, 0.25 inch | 6253W | 9 | Screw, button head, 0.25-20 x 0.750 inch (2) | 923 | |
4 | Clip, special "U" type | 58439-07 | 10 | Mid frame air deflector, left | Not Sold Separately | |
5 | Clamp, cable | 10053 | 11 | Screw, button head, 0.25-20 x 0.875 | 4015 | |
6 | Mid frame air deflector, right | Not Sold Separately |