OVERWATCH THROW-OVER SADDLEBAGS
941005372024-04-30
GENERAL INFORMATION
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
90202693
Safety Glasses, Torque Wrench, Isopropyl alcohol
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Overwatch Throw-Over Saddlebags
Table 2. Kit Contents: Overwatch Throw-Over Saddlebags
Verify that all contents are present in the kit before installing or removing items from vehicle.
Item
Qty
Description
Part No.
Notes
1
2
Reflector, red
Not sold separately
Order Reflector kit (Part No. 57300436). Includes items 1-4.
2
2
Screw
Not sold separately
3
2
Reflector plate, outer
Not sold separately
4
2
Reflector plate, inner
Not sold separately
5
1
Yoke, Center
Not sold separately
Order Throw-Over Yoke kit (Part No. 90202774). Items include 5-7.
6
1
Yoke, Right
Not sold separately
7
1
Yoke, Left
Not sold separately
8
1
Saddlebag, left
90202773
9
1
Transparent paint guard
90202776
10
4
Hook and loop strap
90202775
11
1
Saddlebag, right
90202773
12
2
Inner dry bag
90202777
Not shown
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
    These items are available at your local Harley-Davidson dealership.
  • 2022 and later Nightster models: Separate purchase of Overwatch Throw-Over Saddlebag Support kit (Part No. 90202689) is required for installation.
  • 2018 and later Softail (FLSL, FXBB, FXBBS, FXST): Separate purchase of Saddlebag Support kit (Part No. 90201777) is required for installation.
  • 2006-2017 and later Dyna models: Separate purchase of Saddlebag Support kit (Part No. 91017-10A) is required for installation.
  • 2000 and later XL models (except 1200CX, 1200S, 1200T and 2002-03 883R): Separate purchase of Saddlebag Support kit (Part No. 90201324) is required for installation.
PREPARE
1. Install reflector.
a. If installed, remove inner dry bag.
1Saddlebag (shown transparent)
2Inner reflector plate
3Pre-drilled holes (2)
4Outer reflector plate
5Screw (2)
6Reflector
Figure 4. Reflector Assembly
1.2. See Figure 2. Separate inner (1) and outer (2) saddlebag liners.
1Inner liner
2Outer liner
Figure 2. Gain Access
d. See Figure 4. Install inner reflector plate (2) into saddlebag.
e. Align inner plate (2) holes with pre-drilled holes (3) in saddlebag (1).
f. Align and install outer (4) reflector plate to saddlebag (1).
g. Install screw (5) and tighten.
h. Remove adhesive backing from reflector (6).
i. Adhere reflector directly to outer plate (4).
1.3. See Figure 3. Gain access to bottom of saddlebag and locate mounting holes (1).
1Mounting holes
Figure 3. Mounting Holes
2. Install left and right yokes to saddlebags.
2.1. See Figure 5. Install yoke (1) to saddlebag, zip tight (2).
1Yoke
2Zipper
Figure 5. Install Yoke
2.2. See Figure 6. Secure yoke to saddlebag using Velcro flaps (1).
1Velcro flaps
Figure 6. Velcro Flaps
2.3. See Figure 7. Snap (1) zipper end to saddlebag.
1Snap
Figure 7. Secure with Snap
INSTALL
NOTE
See Installation Requirements for saddlebag support.
Saddlebags can be used with or without a passenger seat. Yoke can be installed under or over passenger seat, whichever fits better depending on model and passenger seat setup.
1. If installed, remove passenger seat.
2. Install saddlebag.
a. See Figure 8. Insert saddlebag support (1) into mesh lining (2).
b. Adjust as needed.
3. Support saddlebag.
4. Install front and rear hook and loop straps (3, 4).
5. Repeat procedure on opposite side.
1Saddlebag support
2Mesh lining
3Rear hook and loop strap
4Front hook and loop strap
Figure 8. Saddlebag Installation
6. See Figure 9. Test fit left (1) and right (2) yokes over rear fender. Do not secure straps at this time.
a. If there is a gap, install center yoke.
b. Velcro center yoke into place.
1Left yoke
2Right yoke
Figure 9. Yoke Installation
7. See Figure 1. Test fit transparent paint guard (9) under yoke pieces.
a. Mark cutting locations on paint guard.
b. Remove yokes pieces from fender area.
c. Clean fender area with 50/50 alcohol and water mixture.
d. Cut paint guard to fit and install.
8. See Figure 10. Install yokes pieces (4, 5)(6 if required) over fender and secure.
a. Connect quick-release buckles (1).
b. Pull on straps to tighten assembly.
c. Secure excess strap (2) in strap bungee (3).
1Quick-release buckle (2)
2Excess strap (2)
3Strap bungee (2)
4Left yoke
5Center yoke
6Right yoke
Figure 10. Yoke Assembled
9. Make overall adjustments as needed.
10. Make sure saddlebag assembly is tightly secured to vehicle.
a. See Figure 11. Make sure there is adequate saddlebag (1) to exhaust clearance (2).
11. If removed, install passenger seat.
1Saddlebag
2Exhaust
Figure 11. Exhaust Clearance
GETTING READY FOR TRAVEL
1. See Figure 12. If using dry bag:
a. Install dry bag into saddlebag.
b. Secure dry bag to saddlebag by using magnetic locks (1, 2).
1Dry bag magnetic lock
2Saddlebag magnetic lock
Figure 12. Dry Bag Install
2. See Figure 13. Roll up (1) top of bag and insert into saddlebag.
1Roll up
Figure 13. Roll Up
3. See Figure 14. Secure saddlebag.
a. Connect quick-release buckles (1).
b. Pull on excess strap (2) to tighten.
c. Secure excess strap (2) in strap bungee (3).
1Quick-release buckle
2Excess strap
3Strap bungee
Figure 14. Secure Saddlebag
MAINTENANCE
1. Use a lint free cloth to wipe off any dust or dirt.
2. Thoroughly clean outer surface with warm water and a mild detergent.
3. Do not use artificial means to dry material quickly.
4. Contains one or more of the following materials:
a. Polyester
b. Polypropylene
c. Polyethylene
d. Polyvinyl chloride