Kits | Suggested Tools | Skill Level(1) |
---|---|---|
90202693 | Safety Glasses, Torque Wrench, Isopropyl alcohol | ![]() |
![]() | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
![]() | 1 | 2 | Reflector, red | Not sold separately | Order Reflector kit (Part No. 57300436). Includes items 1-4. |
![]() | 2 | 2 | Screw | Not sold separately | |
![]() | 3 | 2 | Reflector plate, outer | Not sold separately | |
![]() | 4 | 2 | Reflector plate, inner | Not sold separately | |
![]() | 5 | 1 | Yoke, Center | Not sold separately | Order Throw-Over Yoke kit (Part No. 90202774). Items include 5-7. |
![]() | 6 | 1 | Yoke, Right | Not sold separately | |
![]() | 7 | 1 | Yoke, Left | Not sold separately | |
![]() | 8 | 1 | Saddlebag, left | 90202773 | |
![]() | 9 | 1 | Transparent paint guard | 90202776 | |
![]() | 10 | 4 | Hook and loop strap | 90202775 | |
![]() | 11 | 1 | Saddlebag, right | 90202773 | |
![]() | 12 | 2 | Inner dry bag | 90202777 | Not shown |
1. | Install reflector. a. If installed, remove inner dry bag. | ![]()
Figure 4. Reflector Assembly | ||||||||||||
| ![]()
Figure 2. Gain Access | |||||||||||||
d. Figure 4 Install inner reflector plate (2) into saddlebag. e. Align inner plate (2) holes with pre-drilled holes (3) in saddlebag (1). f. Align and install outer (4) reflector plate to saddlebag (1). g. Install screw (5) and tighten. h. Remove adhesive backing from reflector (6). i. Adhere reflector directly to outer plate (4).
| ![]()
Figure 3. Mounting Holes | |||||||||||||
2. | Install left and right yokes to saddlebags. | |||||||||||||
| ![]()
Figure 5. Install Yoke | |||||||||||||
| ![]()
Figure 6. Velcro Flaps | |||||||||||||
| ![]()
Figure 7. Secure with Snap |
1. | If installed, remove passenger seat. | |||||||||||||
2. | Install saddlebag. a. Figure 8 Insert saddlebag support (1) into mesh lining (2). b. Adjust as needed. | |||||||||||||
3. | Support saddlebag. | |||||||||||||
4. | Install front and rear hook and loop straps (3, 4). | |||||||||||||
5. | Repeat procedure on opposite side. | ![]()
Figure 8. Saddlebag Installation | ||||||||||||
6. | Figure 9 Test fit left (1) and right (2) yokes over rear fender. Do not secure straps at this time. a. If there is a gap, install center yoke. b. Velcro center yoke into place. | ![]()
Figure 9. Yoke Installation | ||||||||||||
7. | Figure 1 Test fit transparent paint guard (9) under yoke pieces. a. Mark cutting locations on paint guard. b. Remove yokes pieces from fender area. c. Clean fender area with 50/50 alcohol and water mixture. d. Cut paint guard to fit and install. | |||||||||||||
8. | Figure 10 Install yokes pieces (4, 5)(6 if required) over fender and secure. a. Connect quick-release buckles (1). b. Pull on straps to tighten assembly. c. Secure excess strap (2) in strap bungee (3). | ![]()
Figure 10. Yoke Assembled | ||||||||||||
9. | Make overall adjustments as needed. | |||||||||||||
10. | Make sure saddlebag assembly is tightly secured to vehicle. a. Figure 11 Make sure there is adequate saddlebag (1) to exhaust clearance (2). | |||||||||||||
11. | If removed, install passenger seat. |
1 | Saddlebag |
2 | Exhaust |
1. | Figure 12 If using dry bag: a. Install dry bag into saddlebag. b. Secure dry bag to saddlebag by using magnetic locks (1, 2). | ![]()
Figure 12. Dry Bag Install | ||||||
2. | Figure 13 Roll up (1) top of bag and insert into saddlebag. | ![]()
Figure 13. Roll Up | ||||||
3. | Figure 14 Secure saddlebag. a. Connect quick-release buckles (1). b. Pull on excess strap (2) to tighten. c. Secure excess strap (2) in strap bungee (3). | ![]()
Figure 14. Secure Saddlebag |
1. | Use a lint free cloth to wipe off any dust or dirt. | |
2. | Thoroughly clean outer surface with warm water and a mild detergent. | |
3. | Do not use artificial means to dry material quickly. | |
4. | Contains one or more of the following materials: a. Polyester b. Polypropylene c. Polyethylene d. Polyvinyl chloride |