ADVERSARY FOOTPEGS - RIDER

941002472023-01-09

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
50502252, 50502253, 50502254, 50502255	Safety glasses, Torque wrench

(1) Tightening to torque value or other moderate tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Adversary Footpegs - Rider

Table 2. Kit Contents: Adversary Footpegs - Rider

	Verify that all contents are present in the kit before installing or removing items from vehicle.
	Item	Qty	Description	Part No.	Notes
	1	1	Footpeg, left, grey, small	50502376
			Footpeg, left, grey, large	50502387
			Footpeg, left, black, small	50502375
			Footpeg, left, black, large	50502386
	2	1	Footpeg, right, grey, small	50502374
			Footpeg, right, grey, large	50502385
			Footpeg, right, black, small	50502373
			Footpeg, right, black, large	50502384
	3	2	Wear peg (not shown)	50500628
Items mentioned in text, but not included in kit
	A	2	Original Equipment (OE) Clevis pin
	B	2	OE Return spring

GENERAL

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

WARNING

Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)

REMOVE

Remove rider footpeg clevis pin (A).

a. Figure 2 Locate locking tab.

b. Push locking tab inward.

c. Using a small screwdriver, push upward and remove clevis pin.

Figure 2. Clevis Pin Locking Tab

	WARNING Wear safety glasses or goggles when removing or installing spring. Spring tension can cause spring, attached components and/or hand tools to fly out which could result in death or serious injury. (00477c)
2.	Remove OE rider footpeg. a. Cover footpeg assembly return spring (B) area with a shop towel. b. See Figure 3 or Figure 4. Pulling footpeg assembly outward, remove assembly from bracket. c. Set aside return spring for future use.

Figure 3. Footpeg - Rider - Right

Figure 4. Footpeg - Rider - Left

INSTALL

1.	Locate new footpeg assembly (1 or 2).
2.	See Figure 5 or Figure 6. Position return spring (B) in to footpeg assembly.
3.	Align return spring with bracket hole.

Figure 5. Return Spring Orientation - Right

Figure 6. Return Spring Orientation - Left

4.	Insert footpeg assembly in to bracket.
5.	Position footpeg assembly to align with clevis pin hole.
6.	From upper side of bracket, install clevis pin (A). a. Verify clevis pin locking tab is fully seated.

Wear Peg Replacement

1.	When servicing wear peg, remove existing wear tip from footpeg.
2.	Apply two or three drops of threadlocker to threads of new wear peg.LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97)
3.	Install new wear peg to footpeg. Torque: 3.38–4.74 N·m (30–42 in-lbs)

COMPLETE

Verify operation.

a. Move footpeg assembly up, return spring should return assembly back in to place.