RIDER FOOTBOARD

J067762024-01-24

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
50501679, 50501648, 50501938, 50501939, 50501945, 50502526, 50502527	Safety Glasses, E-Clip tool

(1) Tightening to torque value or other moderate tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Rider Footboard Components

Table 2. Kit Contents: Rider Footboard Components

	Item	Qty	Description	Part No.	Notes
	1	2	Footboard Assembly, graphite	50502097
			Footboard Assembly, black	50502098
			Footboard Assembly, black	50502487	Kit 50502526
			Footboard Assembly, silver	50502489	Kit 50502527
	2	1	Footboard, left, black	50501940
			Footboard, left, machine cut	50501936
			Footboard, left, chrome	50501948
			Footboard, left, gray	50502335
			Footboard, left, black	50502334
	3	1	Footboard, right, black	50501944
			Footboard, right, machine cut	50501942
			Footboard, right, chrome	50501947
			Footboard, right, gray	50502333
			Footboard, right, black	50502332
	4	2	Spring	50502463	Kits 50501938, 50501939, 50509145
	5	2	Wear plate (see Figure 4 )	50502575	Kits 50502526, 50502527
	6	2	Screw, wear plate (see Figure 4 )	10200659	Kits 50502526, 50502527
Service Part
	A	1	Wear peg	50500628	Kits 50501938, 50501939, 50509145, 50502256, 50502257

NOTE

Verify that all contents are present in the kit before installing or removing items from vehicle.

GENERAL

Models

For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).

Verify that the most current version of the instruction sheet is used. It is available at: www.harley-davidson.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

E-CLIP TOOL (Part Number:HD-52369)

WARNING

Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)

REMOVE

1.	Figure 2 Remove E-clip (3), clevis pin (1) and return torsion spring (2).
2.	Remove footboard.
3.	Save hardware for new footboard installation.
4.	Clean and inspect footboard brackets.
5.	Replace if worn, rusted or damaged.

INSTALL

1.	Install footboard. a. Kits 50501679, 50501648, 50502256, 50502257: Figure 2 Insert short end of Original Equipment (OE) torsion spring (2) into forward most hole in footboard. b. Kits 50501938, 50501939, 50501945: Figure 1 Insert short end of new torsion spring (4) into forward most hole in footboard. c. While holding torsion spring (2) in place, install footboard and torsion spring onto mounting bracket. d. Install clevis pin (1). e. Install E-clip (3). f. Rotate footboard up and push torsion spring (2) into slot on mounting bracket.
2.	Check that footboard pivots freely on clevis pin (1).
3.	Repeat steps 1 and 2 on opposite side.

1	Clevis pin
2	Torsion spring
3	E-clip

Figure 2. Rider Footboard Kit

Wear Peg Replacement

1.	Figure 3 Remove existing wear peg (1) from floorboard.
2.	Apply 2 or 3 drops of threadlocker to threads of new wear peg (1) and install.LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97)
3.	Tighten wear peg (1). Torque: 3.4–4.8 N·m (30–42 in-lbs) Wear peg

Wear peg

Figure 3. Floorboard Wear Peg (typical)

Wear Plate Replacement

1.	Figure 4 When servicing wear plate (1), remove existing wear plate screws (2).
2.	Apply two or three drops of threadlocker to threads of screws.LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97)
3.	Install new wear plate and screws. Torque: 2.03 N·m (18 in-lbs)

1	Wear plate
2	Screw (2)

Figure 4. Floorboard Wear Plate