RIDER FOOTPEG
J067732021-08-02
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
50501641, 50501684, 50502020 | Safety Glasses, Torque Wrench, E-Clip Tool, Loctite 243 Blue |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Rider Footpeg Components
Table 2. Kit Contents: Rider Footpeg Components
 | Item | Qty | Description | Part No. | Notes |
|---|---|---|---|---|---|
 | 1 | 1 | Footpeg, rider right side, graphite | 50501685 | |
| 1 | Footpeg, rider right side, black | 50501686 | ||
| 1 | Footpeg, rider right side, black | 50502018 | ||
| 2 | 1 | Footpeg, rider left side, graphite | 50501687 | |
| 1 | Footpeg, rider left side, black | 50501688 | ||
| 1 | Footpeg, rider left side, black | 50502019 | ||
| 3 | 2 | Wear peg | 50501135 |
NOTE
Verify that all contents are present in the kit before installing or removing items from vehicle.
GENERAL
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Verify that the most current version of the instruction sheet is used. It is available at: www.harley-davidson.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
REMOVE
| 1. | Softail models: See Figure 2. Remove pin (4) and E-clip (2). Retain for later use. | |
| 2. | Models equipped with Revolution Max engines: See Figure 4. Depress spring loaded detent and remove clevis pin (1). | |
| 3. | Save all hardware including torsion spring (1) for installation of new footpegs (3). |
INSTALL
| 1. | See Figure 2. Insert short leg of torsion spring (1) into hole in new footpeg (3). NOTE When performing the next step, verify that the torsion spring is positioned inside of the footpeg. | |
| 2. | Align long leg of torsion spring (1) to hole in footpeg mount and insert. | |
| 3. | Rotate footpeg (3) into position in clevis and insert clevis pin (4) through clevis, footpeg (3) and torsion spring (1). | |
| 4. | Softail models: Install E-clip (2). Special Tool: E-CLIP TOOL (HD-52369) | |
| 5. | Models equipped with Revolution Max engines: See Figure 4. Install clevis pin (1). | |
| 6. | Repeat steps for other side. |
Wear Tip Replacement
| 1. | When servicing wear tip, remove existing wear tip from footpeg. | |
| 2. | Apply two or three drops of threadlocker to threads of new wear tip.LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97) | |
| 3. | Install new wear tip to footpeg. Tighten. Torque: 3.38–4.74 N·m (30–42 in-lbs) |
| 1 | Torsion spring |
| 2 | E-clip |
| 3 | Footpeg |
| 4 | Clevis pin |
Figure 2. Rider Footpeg Torsion Spring Installation
| 1 | Footpeg |
| 2 | Torsion spring |
| 3 | Clevis pin |
| 4 | Bracket |
| 5 | Hole |
Figure 3. Remove/Install Footpeg Assembly w/ Spring Loaded Detent
| 1 | Clevis pin |
| 2 | Footpeg, rider |
| 3 | Decorative screws |
Figure 4. Install Footpeg Assembly w/ Spring Loaded Detent
NOTE
See Figure 4. Screws on centerline of footpegs are for decorative purpose only. Do not tighten.