QUICK-RELEASE SISSY BAR UPRIGHT KIT
J057602024-01-19
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
52300324A, 52300415 | Safety Glasses, Torque Wrench |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Quick-Release Sissy Bar Upright Kit
Table 2. Kit Contents: Quick-Release Sissy Bar Upright Kit
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Upright, backrest, chrome | Not sold separately | |
1 | Upright, backrest, black | Not sold separately | |||
| 2 | 2 | Backrest dock assembly, chrome | 52300326A | |
2 | Backrest dock assembly, black | 52300419 | |||
| 3 | 4 | Screw | 94595-98 | |
| 4 | 1 | O-ring service kit | 91700038 | Includes small and large diameter O-rings |
| 5 | 2 | Plug, chrome | 12100080 | |
2 | Plug, black | 12100098 | |||
GENERAL
NOTE
This instruction sheet may have a Supplemental Video to assist installer in clarifying a certain part of the assembly. A linked video would be located at the end of this instruction sheet.
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
This item is available from a Harley-Davidson dealer.
- Electrical Contact Lube (Part No. 11300004) or equivalent, is required for proper installation of this kit.
REMOVE
| 1. | See Figure 2. Remove trim covers (2) from body (1). a. To prevent damage to paint, use plastic prying tool or equivalent. |
| 1 | Body |
| 2 | Cover |
| 3 | Backrest dock |
| 4 | Screw (2) |
Figure 2. Trim Cover
INSTALL
| 1. | See Figure 2. Install backrest docks (3) to body (1). | |
| 2. | Install two screws (4) for each dock. Tighten. Torque: 13.6 N·m (120 in-lbs) | |
| 3. | See Figure 3. Align and install upright. a. Press release button (1) on backrest dock while inserting one leg of upright. b. Press release button (1) on other backrest dock while inserting opposite leg of upright. | |
| 4. | While holding both legs of upright, firmly press upright further into backrest docks. a. Release buttons must return to original, extended position to complete installation. | |
| 5. | See Figure 1. If fit of upright in docks is not snug, remove installed O-rings and replace with larger diameter O-rings. Repeat steps 3 and 4. a. A small amount of electrical contact lube can be applied to surface of each O-ring to aid in installation. |
| 1 | Release button |
| 2 | Backrest dock |
Figure 3. Release Button Locked Position
PLUG
NOTE
Plugs do not require or use O-rings.
| 1. | See Figure 1. When upright (1) is removed, install plugs (5). | |
| 2. | Follow steps 3-5 for installing or removing upright. Refer to INSTALL. |