HEEL SHIFTER
941000852019-08-21
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) | Time |
|---|---|---|---|
33600325, 33600345 | Safety Glasses, Torque Wrench, Grease Pencil |  | 30 minutes |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Heel Shifter Components
Table 2. Kit Contents: Heel Shifter Components
 | Item | Qty | Description | Part No. | Notes |
|---|---|---|---|---|---|
 | 1 | 1 | Shift lever, heel/toe, Kit 33600325 | Not sold separately | |
| 1 | Shift lever, black, Kit 33600345 | Not sold separately | ||
| 2 | 1 | Spacer, shifter shaft | 5817 | |
| 3 | 1 | Nut | 7686 | |
| 4 | 1 | Rubber peg, shifter | 34590-08 | |
| 5 | 1 | Peg, stud | 34591-08 | 12–16 N·m (9–12 ft-lbs) |
| 6 | 1 | Screw, SEMS | 10200350 | 12–16 N·m (9–12 ft-lbs) |
Items mentioned in text, but not included in kit | |||||
| A | 1 | Original Equipment (OE) Shift lever | ||
| B | 1 | OE Rubber peg, shifter | ||
| C | 1 | OE Peg, stud | ||
| D | 1 | OE Nut | ||
| E | 1 | OE Screw, SEMS | ||
| F | 1 | OE Shaft, shifter | ||
| G | 1 | OE Spacer, shifter shaft | ||
NOTE
Verify that all contents are present in the kit before installing or removing items from vehicle.
GENERAL
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Verify that the most current version of the instruction sheet is used. It is available at: www.harley-davidson.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
PREPARE
| 1. | Mark position of toe shifter with a grease pencil before removal. |
REMOVE
| 1. | Remove toe shifter (A). | |
| 2. | Retain hardware. | |
| 3. | Remove OE long spacer (G). |
INSTALL
| 1. | Install short spacer (2) from kit. | |
| 2. | Install toe shifter, inboard (A). a. Align screw (E) to groove. b. Secure screw (E) and nut (D). Tighten. Torque: 12–16 N·m (9–12 ft-lbs) | |
| 3. | Install heel shifter, outboard (1). a. Align screw (6) to groove. b. Secure screw (6) and nut (3). Tighten. Torque: 12–16 N·m (9–12 ft-lbs) | |
| 4. | Install peg stud (5) through rubber peg (4). Tighten. Torque: 12–16 N·m (9–12 ft-lbs) | |
| 5. | Ensure there is full travel to perform upshifts and downshifts. | |
| 6. | Levers should be approximately 160° apart. |