TANK BAG PAN AMERICA

941002422022-09-26

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
93300129	Safety Glasses

(1) Only simple tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Tank Bag Kit

Table 2. Kit Contents: Tank Bag Kit

Verify that all contents are present in the kit before installing or removing items from vehicle.
Item	Qty	Description	Part No.	Notes
1	1	Bag, tank	Not sold separately
2	2	Screw	10201138
3	2	Washer	10300236
4	2	O-ring	11159
5	2	Spacer	12400206
6	1	Strap, front	93300154
7	1	Strap set, tank, rear	93300146
8	1	Rain cover	93300152
9	2	Protective tape	11100303

GENERAL

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

WARNING

Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)

NOTE

This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:

A Harley-Davidson dealer.
H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.

WARNING

See ACCESSORIES AND CARGO section within the SAFETY FIRST section in your owner's manual. Improper cargo loading or accessory installation can cause component failure and adversely affect stability, handling and performance, which could result in death or serious injury. (00021c)

Do not exceed 5 lbs (2.3 kg) total weight contents and attachments.
Verify that all straps are secured.
Periodically recheck load.

WARNING

Do not exceed the motorcycle's Gross Vehicle Weight Rating (GVWR) or Gross Axle Weight Rating (GAWR). Exceeding these weight ratings can lead to component failure and adversely affect stability, handling and performance, which could result in death or serious injury. (00016f)

GVWR is the total weight of the motorcycle, accessories, rider, passenger and cargo that can be safely carried.
GAWR is the maximum amount of weight that can be safely carried on one axle.
GVWR and GAWR are shown on the information plate, located on the frame downtube.

PREPARE

Remove seat. See service manual.

REMOVE

Figure 2 Remove Original Equipment (OE) screws (1) from tank console (2). Discard.

1	OE Screw (2)
2	Tank console

Figure 2. Tank Console

INSTALL

1.	Figure 3 Install front mounting straps to tank console. a. Figure 3 Install spacer (1), mounting strap (2), O-ring (3), washer (4) and screw (5). NOTE Install spacer (1) with grooved side facing toward tank. b. Secure screw (5). Tighten. Torque: 3.9–4.8 N·m (35–42 in-lbs)
2.	Figure 4 Install rear strap (1) under tank (2). a. Thread rear strap between rear tank mount and tank. b. Pull buckle through loop at other end of strap. c. Eliminate slack in strap system.
3.	Figure 5 Position tank bag on tank.
4.	Figure 7 Secure front mounting straps to tank bag by connecting quick release buckles.
5.	Figure 7 Secure rear mounting strap to tank bag by connecting quick release buckle.
6.	Pull straps snug to eliminate slack in strap system.
7.	Install protective tape to fuel tank. a. Figure 6 Check for widest point (1) of tank bag. b. Test fit protective tape (1) where tank bag touches the fuel tank. Note location. c. Remove tank bag (3). d. Clean area with 50/50 alcohol and water mixture. e. Wipe dry with clean cloth. f. Peel backing from protective tapes (1) and install in noted location.. g. Install tank bag (3).

1	Spacer (2)
2	Strap (2)
3	O-ring (2)
4	Washer (2)
5	Screw (2)

Figure 3. Front Strap Install

Figure 4. Rear Strap Install

Figure 5. Tank Bag Installed

1	Protective tape (2)
2	Widest point
3	Tank bag

Figure 6. Protective Tape

1	Quick release (disconnected)
2	Quick release (connected)
3	Strap bungee

Figure 7. Quick Release Buckle

Figure 8. Front Straps in Stowed Position

COMPLETE

NOTE

Zipper pulls have loops so that a small lock can be used for added security.

1.	Install seat. After installing seat, pull up on seat to verify that it is secure. See service manual.
2.	Pull straps tight to secure bag.
3.	Check that bag is securely fastened to vehicle.
4.	Figure 7 Secure any excess strap length using strap bungee (3).
5.	Figure 8 Clip front two straps (1,2), attached to tank console, together when tank bag is removed from vehicle. a. Figure 7 Secure excess strap length using strap bungee (3).

RAIN COVER

1.	Pull rain cover over entire bag.
2.	Pull draw string at bottom of cover to tighten.
3.	Secure with barrel lock
4.	Make sure the rain cover is tucked completely under tank bag.

Figure 9. Rain Cover Installed

MAINTENANCE

1.	Use a lint-free cloth to wipe off any dust or dirt.
2.	Thoroughly clean outer surface with warm water and a mild detergent.
3.	Allow material to dry naturally and completely before use or storage.
4.	Do not use washing machine or dryer.
5.	Do not use artificial means to dry material quickly.
6.	Contains one or more of the following materials: Polyester, Polypropylene, POM, EPDM Rubber, Vinyl.