MIRROR KIT
941001922022-08-08
GENERAL INFORMATION
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
56000220, 56000221, 56000241, 56000261
Safety Glasses, Torque Wrench
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Mirror Kit
Table 2. Kit Contents: Mirror Kit
Verify that all contents are present in the kit before installing or removing items from vehicle.
Item
Qty
Description
Part No.
Notes
1
1
Left mirror
56000240
Left mirror, round
56000271
Left mirror, Empire, Black
56000215
Left mirror, Empire, Edge cut
56000217
2
1
Right mirror
56000236
Right mirror, round
56000273
Right mirror, Empire, Black
56000216
Right mirror, Empire, Edge cut
56000218
3
1
Right mirror nut
10100136
Kit 56000241 Only
Right mirror nut, black
10100149
4
1
Right clamp half
41700623
5
1
Left clamp half
36700236
6
1
Left mirror nut
10100135
Kit 56000241 Only
Left mirror nut, black
10100150
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
    These items are available at your local Harley-Davidson dealership.
  • Separate purchase of Handlebar End Cap (Part No. 55801095, 55900246, 55900247 or 55900248) is required for installation.
REMOVE
For all models except RA1250S:
1. See Figure 2. Remove Original Equipment (OE) bar end mirror.
a. Remove and discard screw (1).
b. Remove and discard mirror base (2).
2. Install handlebar end caps. Refer to Installation Requirements.
3. See Figure 3. Remove screws (4) from OE clamp half on clutch and front master cylinder. Save for later use.
4. Remove and discard OE clamp half (3).
1Screw
2Mirror base
Figure 2. Bar End Mirror
For model RA1250S:
1. See Figure 3. Loosen mirror nut (2) and remove mirror.
2. Leave end caps and mirror half clamps on vehicle.
INSTALL
NOTE
Clutch lever clamp half will have number 36700236 imprinted on component.
Left mirror has right hand threads. Right mirror has left hand threads.
For all models except RA1250S:
1. See Figure 3. Install new clamp half (3).
2. Position hand control as needed.
3. Install screws (4). Do not tighten completely.
a. Fully seat and tighten top screw (4).
Torque: 7–9 N·m (62–80 in-lbs)
b. Fully seat and tighten bottom screw (4).
Torque: 7–9 N·m (62–80 in-lbs)
4. Install mirror.
a. Install mirror nut (2) onto mirror stem until loosely seated.
b. Loosely install mirror (1) into clamp half (3).
c. Adjust mirror stem (1) position.
d. Tighten mirror nut (2) against clamp half (3). Careful not to damage nut finished surface.
Torque: 12–14 N·m (106–124 in-lbs)
5. Repeat procedure for opposite side.
1Mirror
2Mirror nut
3Clamp half
4Screw
Figure 3. Mirror Assembly
For model RA1250S:
1. See Figure 3. Install mirror.
a. Install mirror nut (2) onto mirror stem until loosely seated.
b. Loosely install mirror (1) into clamp half (3).
c. Adjust mirror stem (1) position.
d. Tighten mirror nut (2) against clamp half (3). Careful not to damage nut finished surface.
Torque: 12–14 N·m (106–124 in-lbs)