H-D DETACHABLES TOURING TWO-UP TOUR-PAK RACK
J047562014-06-30
GENERAL
Kit Number
53276-09B
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
Separate purchase of extra parts or accessories may be required for proper installation of this H-D® Detachables™ Tour-Pak® Rack Kit. See the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only) for a list of required parts or accessories.
WARNINGRider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
WARNINGDo not exceed Tour-Pak weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00401c)
NOTE
See label inside Tour-Pak, operator's manual, Tour-Pak installation instructions for weight capacity limits.
Maximum Tour-Pak luggage rack weight capacity is 10 pounds (4.5 Kg).
INSTALLATION
Tour-Pak Installation to Rack
| 1. | Open the Tour-Pak lid and, if necessary, remove all items from inside the Tour-Pak. Models with rubber mat: Remove the mat. Models with molded liner: Open the map pocket. Remove the acorn nuts with flat washers. Remove the map pocket and liner. ALL models: Close the lid. NOTE See Figure 1. When installing the Tour-Pak to the rack in the following steps: note holes in the Tour-Pak mounting plate (1) provide forward (3) and rearward (2) positions for mounting the Tour-Pak. | |||||||||
| 2. | Place the Tour-Pak on the Tour-Pak rack, and open the lid. Align the forward or rearward holes in the Tour-Pak mounting plate with the holes in the rack. | 
Figure 1. Tour-Pak Mounting Plate | ||||||||
| 3. | See Figure 3. Obtain the hex head cap screws (10), locknuts (12) and plain washers (11) from the kit. Place a washer over the threads of each screw. Insert the screw threads down through the Tour-Pak mounting plate and floor, and into the holes in the rack. NOTE Always install the mounting screws from inside the Tour-Pak. If the screws are installed from the bottom, the screw ends can tear the molded liner and scratch objects, such as helmets, stored inside the Tour-Pak. | |||||||||
| 4. | From the underside of the rack, install a washer and locknut onto the threads of each screw. In a crosswise pattern, alternately tighten each screw to 13.5 N·m (120 in-lbs). | |||||||||
| 5. | Install the rubber mat or molded liner into the Tour-Pak. Close and latch the Tour-Pak lid. | |||||||||
| 6. | Install the Detachable Docking Hardware Kit to the vehicle per the instructions in that kit. |
Tour-Pak and Rack Installation to Docking Points
| 7. | See Figure 3. Stand behind the motorcycle. Place the left side and right side front Tour-Pak rack notches (C, with bushings in place) onto the front docking points on the docking plates (E). Make sure the notch bushings (9) seat fully into the front docking points. | 
Figure 2. Proper Alignment of Latch in Rear Docking Point, View in Direction of Arrow (F) | ||||||||||||||
| 8. | See Figure 3 , arrow (F) and Figure 2. Position the rotary latches (4) over the rear docking points (3). Check the rack sides (1) and latches fit into the neck (7) of the rear docking points as shown. This may require some gentle squeezing or spreading of the rack sides. | |||||||||||||||
| 9. | Push the rear of the rack downward and close the latches by pressing the latch lever as far forward as it goes. You hear a "CLICK" when the latch is in place. If the latch does not easily close, do not force. Check the rack alignment again, as described in steps 7 and 8. | |||||||||||||||
| 10. | To remove the Tour-Pak and rack, press the release button (G) on each side and pull the latch levers back. Carefully lift the rear of the Tour-Pak rack up. Pull the rack out of the front docking points. |
NOTE
After installing the Tour-Pak rack, check the Tour-Pak and rack are secure. The front and rear docking points must be fully engaged. See Figure 2 for correct engagement.
SERVICE PARTS
Figure 3. Service Parts, H-D Detachables Touring Two-Up Tour-Pak Rack
Table 1. Service Parts Table
Item | Description (Quantity) | Part Number |
|---|---|---|
1 | Detachable two-up Tour-Pak rack assembly (includes items 2, 3, 4) | Not sold separately |
2 |
| Not sold separately |
3 |
| Not sold separately |
4 |
| 50300108 |
5 |
| Not sold separately |
6 |
| 6828 |
7 |
| 6827 |
8 |
| 2957 |
9 | Bushing (2) | 52682-09 |
10 | Hex head cap screw (4) | 3802W |
11 | Flat washer (8) | 6703 |
12 | Hex lock nut (4) | 7887 |
Items mentioned in text, but not included in kit: | ||
A | Mounting locations for Original Equipment, King or Chopped Tour-Pak luggage | |
B | Mounting locations for Leather Tour-Pak luggage | |
C | Front Tour-Pak rack notch (2) | |
D | Rear Tour-Pak rack notch (2) | |
E | Four-point docking plate assembly (2) | |
F | To front of vehicle (view direction for Figure 2) | |
G | Rotary latch release button (2) | |