UNIVERSAL PHONE CARRIER PLUS CLUTCH MOUNT
941002302023-01-09
GENERAL INFORMATION
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
76001071, 76001339
Safety Glasses, Torque Wrench, Isopropyl alcohol
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Universal Phone Carrier w/ Clutch Mount
Table 2. Kit Contents: Universal Phone Carrier w/ Clutch Mount
Verify that all contents are present in the kit before installing or removing items from vehicle.
Item
Qty
Description
Part No.
Notes
1
1
Clutch Mount
Not sold separately
2
1
Universal interface
76001081
3
1
Screw
Not sold separately
1
Screw, M6
Not sold separately
Sportster XL, Street XG, Pan America, RH models
4
1
Washer
Not sold separately
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
REMOVE
1. See Figure 2. Remove upper screw (2) and washer (1) from left side clutch mount. Discard.
2. Livewire Models: See Figure 2. Remove upper screw (2) and washer (1) from left side mirror mount. Discard.
INSTALL
Universal Phone Mount
1. Prior to tightening phone mount bolt (3), adjust clocking to enable viewing without obstructing functions of the motorcycle.
2. Touring, Trike, Softail, Dyna, Livewire Models: See Figure 3. Install screw (3) and lockwasher (4) to left side clutch mount. Tighten.
Torque: 6.78–9.03 N·m (60–80 in-lbs)
3. Sportster XL, Street XG, Pan America, RH Models: See Figure 3. Install M6 screw (3) and lockwasher (4) to left side mirror mount. Tighten.
Torque: 6.78–9.03 N·m (60–80 in-lbs)
4. See Figure 4. Loosen screw (B) to adjust orientation on clamp pivot. Tighten.
Torque: 6.78–9.03 N·m (60–80 in-lbs)
5. See Figure 4. Loosen screw (C) on phone interface (3) to adjust phone clocking. Tighten.
Torque: 1.58–1.92 N·m (14–17 in-lbs)
1Lockwasher
2Screw
Figure 2. Upper Left Side Clutch/Mirror Mount Screw and Washer
1Phone mount
3Screw
4Lockwasher
Figure 3. Phone Mount Install to Left Side Clutch/Mirror Mount
1Clutch perch
2Clamp pivot, rotates and pivots up/down
3Phone interface pivot, rotates
AScrew, clutch perch
BScrew, clamp
CScrew, interface
Figure 4. Pivot Points
Universal Interface
NOTE
  • Contaminated or oily surfaces can cause improper adhesion and can result in loss or damage to phone.
  • Some smart phones have non-stick or water resistant nano-particle coatings that repel the adhesive or have removable battery covers that could come loose.
  • Adhesive will not adhere to rough, uneven surfaces.
  • Smooth and non-porous surface areas of at least 2.16 in. (55mm) x 2.56 in. (65mm) is needed for interface to be placed on.
  • Position adapter carefully. Adhesive mount cannot be reused.
  • It is the owner's responsibility to verify a good adhesive bond strength between phone case and universal interface.
  • For more information on phone cases with interface built in and not requiring adhesive, go to www.harley-davidson.com and search for appropriate phone mount kit.
1. See Figure 1. Install universal interface (2).
a. Clean phone case with isopropyl alcohol. Let dry before application of phone surface.
b. Apply adhesive at room temperature.
c. Apply firm pressure between universal interface and phone case for one minute.
d. Allow adhesive bond to cure for 48 hours before using universal interface to support phone.
Phone Install
1. See Figure 5. Install phone to mount.
a. Align and insert tabs on phone interface to slots on phone case.
NOTE
Gently pull on phone to verify that it is properly installed and mount is locked
b. Turn phone a ¼ turn until phone settles into the next detent.
2. Adjust phone mount and phone orientation as needed for optimal access and viewing.
1Mounting positions
2Arm positions
3Adjust micro rail head
4Phone placement
5Turn 90°
6Locked position
APortrait position
BLandscape position
Figure 5. Phone Mount and Positioning Options
COMPLETE
WARNING
Be sure that steering is smooth and free without interference. Interference with steering could result in loss of vehicle control and death or serious injury. (00371a)
1. Turn handlebar lock to lock after installation to verify that the phone carrier and phone do not interfere with fairings, gas tank, cables, lines, hoses, wiring or other equipment.
2. Make sure that the phone does not obscure visibility of speedometer, hand controls, indicator lights or mirrors.