0/0
S2MH TWO UP KIT
941006692024-08-29
GENERAL INFORMATION
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
50503188, 50700141, 50700142, 50700143
Safety Glasses, Torque Wrench, Loctite 243 Medium Strength Threadlocker and Sealant (Blue)
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: S2MH Two Up Kit
Table 2. Kit Contents: S2MH Two Up Kit
Verify that all contents are present in the kit before installing or removing items from vehicle.
Item
Qty
Description
Part No.
Notes
1
6
Screw, flange head
10201366
2
1
Pad, backrest (black)
Not sold separately
Pad, backrest (grey)
Not sold separately
Pad, backrest (red)
Not sold separately
3
1
Support bracket, backrest
Not sold separately
4
1
Strap, helmet
Not sold separately
5
1
Seat, passenger pillion (black)
Not sold separately
Seat, passenger pillion (grey)
Not sold separately
Seat, passenger pillion (red)
Not sold separately
6
1
Strap, passenger grab (black)
Not sold separately
Strap, passenger grab (grey)
Not sold separately
Strap, passenger grab (red)
Not sold separately
7
2
Washer
10300078
8
2
Screw, button head
10201189
9
1
Footpeg, passenger (left)
50502115
10
2
Pin, clevis, footpeg
50501782
11
2
Spring, detent
50500706
12
2
Ball, detent
50500707
13
2
Plate, detent
50500705
14
4
Screw, SEMS
10201004
15
1
Bracket, passenger footpeg (left)
50502232
16
1
Bracket, passenger footpeg (right)
50502233
17
1
Footpeg, passenger (right)
50502116
GENERAL
Models
Confirm all contents are present in the kit before installing or removing items from the vehicle. For model fitment information and to verify the most current version of the instruction sheet is used, see the product listing in the Accessories & Upgrades section of www.LiveWire.com..
Contact LiveWire Customer Support Center at 1-414-343-4122 or toll free at 1-855-EVRider (1-855-387-4337). Visit www.LiveWire.com. for additional information.
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a LiveWire dealer perform the installation. Improper installation of this kit could result in death or serious injury. (16004a)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
PREPARE
1. See Figure 2. Remove rider seat (1). See owners manual.
1Seat
2Seat screw (2)
3Seat tab (2)
4Frame tab (2)
Figure 2. Remove rider seat
2. See Figure 3. Remove rear fender cowl (2). See Helmet Locks, solo seat section of owners manual.
1Key cylinder
2Fender cowl
3Tab
4Hook
5Post
6Latch
Figure 3. Rear fender cowl removal
3. See Figure 4. Remove rear frame hole plugs (1).
1Hole plugs (4)
Figure 4. Rear frame hole plugs
ASSEMBLE
1. See Figure 1. Assemble backrest and seat pillion.
a. Install backrest pad (2) into bracket (3) and secure with screws (1). Tighten.
Torque: 10.4–11.4 N·m (92–101 in-lbs)
b. Install backrest assembly into passenger seat pillion (5) and secure with screws (1). Tighten.
Torque: 10.4–11.4 N·m (92–101 in-lbs)
2. See Figure 5. Assemble right passenger footrest.
a. Install spring (8) and ball (7) into right footrest (6).
b. Hold detent ball in place while installing detent plate (13) to prevent detent ball from falling out.
c. Detent plate should be oriented with the detent holes on the bottom so that they align with the detent ball.
d. Make sure detent ball is aligned with the innermost hole in the detent plate when installed.
e. Install right footrest assembly into right footrest bracket (2).
f. Install clevis pin (3) from top taking care to ensure spring loaded detent (4) extends after complete installation.
1Washer (2) (captured on bolt)
2Bracket
3Clevis pin
4Spring loaded detent
5Detent plate
6Passenger footrest
7Ball
8Spring
9Screws (2)
Figure 5. Passenger footrest assembly
3. Repeat steps for left passenger footrest.
INSTALL
1. See Figure 5. Install right passenger footrest assembly into right frame tail section and secure with screws (9). Tighten.
Torque: 25–29 N·m (18–21 ft-lbs)
2. Install left passenger footrest assembly into left frame tail section and secure with screws (9). Tighten.
Torque: 25–29 N·m (18–21 ft-lbs)
3. See Figure 1. Install passenger grab strap (6).
a. See Figure 6. Locate grab strap mounting holes in frame tail section beneath rider seat.
b. See Figure 1. Apply thread locket to screw (8).LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97)
c. Install passenger grab strap (6) with washer (7) and screw (8). Tighten.
Torque: 4–5 N·m (35–44 in-lbs)
1Mounting holes in frame tail section (2)
Figure 6. Passenger grab strap mounting holes
COMPLETE
1. See Figure 2. Install rider seat (1). Insert rear of rider seat in loop formed by passenger seat strap. See owners manual.
2. See Figure 3. Latch and lock passenger seat assembly in place of rear cowl.
a. Align tab on front of passenger seat with slot in fender.
b. Lower rear of passenger seat assembly until post (5) engages latch (6) ensuring that grab strap is looped over rider seat.
c. Verify passenger seat is properly installed and latched into position by pulling on seat and backrest.
OPERATION
1. Helmet lock operation is unchanged. See owners manual.
a. Remove passenger seat assembly in same manner as removing rear fender cowl. See owners manual.
b. See Figure 1. An additional helmet lock strap (4) is included in this kit.
c. See Figure 2. Loop helmet lock strap through D rings on helmet and secure strap to hook (4).
d. Install passenger seat assembly with helmet straps exiting side of seat through spaces provided. See owners manual.
MAINTENANCE
1. For a complete list of cleaning and care products available for use on the components in this kit, see owners manual.