STAGE I & II SPEAKER KIT-FRAME MOUNTED FAIRING (PN 76001297 and 76001298)
941003652024-10-25
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
76001297, 76001298 | Safety Glasses, Torque Wrench |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Stage I & II Speaker
Table 2. Kit Contents: Stage I & II Speaker
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Grille assembly, left, Stage 1 Speaker | 76001148 | |
| 1 | 1 | Grille assembly, left, Stage 2 Speaker | 76001146 | |
| 2 | 1 | Stage 1 speaker, left, 6.5 inch | 76000998 | |
| 2 | 1 | Stage 2 speaker, left, 6.5 inch | 76000999 | |
| 3 | 1 | Stage 1 speaker, right, 6.5 inch | 76001010 | |
| 3 | 1 | Stage 2 speaker, right, 6.5 inch | 76001011 | |
| 4 | 1 | Grille assembly, right, Stage 1 Speaker | 76001149 | |
| 4 | 1 | Grille assembly, right, Stage 2 Speaker | 76001147 | |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Fits: 2023 CVO Street Glide (FLHXSE), Road Glide (FLTRXSE) and 2024 Street Glide (FLHX), Road Glide (FLTRX).
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
This item is available at a Harley-Davidson dealership.
- 2024-later FLTRX: Separate purchase of Amplifier Kit (Part No. 76001294) is required for this installation.
Installation by a technician at a Harley-Davidson dealership is recommended.
To ensure proper audio performance, speaker set up in the Infotainment Control Unit (IFCU) OR Digital Technician II (DT II) is required for audio configuration and amplifier firmware update.
NOTE
Ensure to select the proper stage speaker during set up for proper audio functionality and speaker performance. If the wrong stage is selected, this may lead to poor speaker performance and damage.
PREPARE
NOTE
Models with security: Disable security system.
| 1. | Remove left saddlebag. See service manual. | |
| 2. | Remove left side cover. See service manual. | |
| 3. | Remove main fuse. See service manual. |
REMOVE
NOTE
New speaker components are shown in graphic, Original Equipment Manufacturer (OEM) is similar.
| 1. | See Figure 2. Remove Original Equipment (OE) speaker grille (8). a. Using a non-marring tool, pry clips (5) from clip openings (3, 4). | |
| 2. | Remove speaker screws (1). | |
| 3. | See Figure 3. Remove OE speaker. a. Remove speaker (1) from fairing far enough to gain access to connectors (4). b. Disconnect connectors (4) from speaker terminals (2). | |
| 4. | Repeat procedure for opposite side. |
| 1 | Screw (4) |
| 2 | Speaker |
| 3 | Outer clip opening |
| 4 | Inner clip opening |
| 5 | Outer upper clip |
| 6 | Inner upper clip |
| 7 | Tab (2) |
| 8 | Grille |
Figure 2. Speaker and Grille (Stage 2 shown, OE similar)
| 1 | Speaker |
| 2 | Terminal (2) |
| 3 | Alignment hole |
| 4 | Connector (2) |
| 5 | Pin |
Figure 3. Fairing Speaker Connection
INSTALL
| 1. | See Figure 4. Orient Stage I (2, 5) or II (3, 4) speaker as shown. | |
| 2. | See Figure 3. Install Stage I or II speaker. a. Connect connectors (4) to speaker terminals (2). b. Install speaker (1) into enclosure. | |
| 3. | See Figure 2. Install speaker screws. a. Alternately secure screws (1). b. Tighten. Torque: 1–1.5 N·m (9–13 in-lbs) | |
| 4. | Install grille. a. See Figure 5. Verify clips (1) and gasket (2) are in place on grille. b. See Figure 2. Install lower tabs (7) onto fairing. c. Rotate grille (8) toward fairing. d. Press grille outer upper clip (5) into outer clip opening (3). e. Press grille inner upper clip (6) into inner clip opening (4). |
| 1 | Left OE Speaker |
| 2 | Left Stage 1 speaker |
| 3 | Left Stage 2 speaker |
| 4 | Right Stage 2 speaker |
| 5 | Right Stage 1 speaker |
| 6 | Right OE Speaker |
Figure 4. Speaker Orientation (Typical)
| 1 | Clip (2) |
| 2 | Gasket |
Figure 5. Grille Gasket
COMPLETE
NOTE
To prevent possible damage to the sound system, verify that the ignition is OFF before installing the main fuse.
| 1. | Install main fuse. See service manual. | |
| 2. | Install left side cover. See service manual. | |
| 3. | Install left saddlebag. See service manual. | |
| 4. | Turn the ignition ON, but do not start the vehicle. | |
| 5. | Make sure that all speakers are working properly. Check that front and rear fader function is operating correctly. If not, check speaker wiring. |