ENGINE GUARD FOOTPEG BILLET MOUNTING KIT

941000252026-01-13

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
50957-02C, 50957-02D, 54234-01A, 54234-01B, 50503333, 50503334	Safety glasses, Torque wrench

(1) Tightening to torque value or other moderate tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Engine Guard Footpeg Billet Mounting

Table 2. Kit Contents: Engine Guard Footpeg Billet Mounting Kit

	Verify that all contents are present in the kit before installing or removing items from vehicle.
	Item	Qty	Description	Part No.	Notes
	1	2	Clamp, chrome	51009-02A	Kit: 50957-02C
				51009-02B	Kit: 50957-02D
				50503278	Kit: 50503334
			Clamp, black	50500017	Kit: 54234-10A
				50500017A	Kit: 54234-10B
				50503277	Kit: 50503333
	2	2	Spring washer	50912-72	ALL Kits
	3	2	Billet footpeg mount, chrome	50501293	Kit: 50957-02C
			Billet footpeg mount, chrome	50501293A	Kit: 50957-02D
			Billet footpeg mount, black	50501292	Kit: 54234-10A
			Billet footpeg mount, black	50501292A	Kit: 54234-10B
		1	Billet footpeg mount, right, black	50503216	Kit: 50503333
			Billet footpeg mount, left, black	50503217	Kit: 50503333
			Billet footpeg mount, right, chrome	50503214	Kit: 50503334
			Billet footpeg mount, left, chrome	50503215	Kit: 50503334
	4	4	Screw, socket head	4617	Kits: 50957-02C, 54234-10A
	4	4	Screw, socket head	10201579	Kits: 50957-02D, 54234-10B, 50503333, 50503334
	5	2	Pin, clevis	45041-01A	Kits: 50957-02C, 50957-02D, 54234-10A, 54234-10B
	5	2	Pin, clevis	50500501	Kits: 50503333, 50503334
	6	2	Retaining ring	11304	ALL Kits
Items mentioned in text, but not included in kit
	A	-	Position this part of the bracket toward the motorcycle
NOTE Orient clamp (1) so angled edge of clamp (1) is on same side as angled edge of foot peg mount (3).

GENERAL

Instruction sheet is also available electronically. To verify you are using the most current version available, do one of the following:

Go to h-d.com/isheets
Scan QR code in upper left corner of the instruction sheet

NOTE

This instruction sheet may have a Supplemental Video to assist installer in clarifying a certain part of the assembly. A linked video would be located at the end of this instruction sheet.

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

WARNING

Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)

This kit requires installing a set of footpegs, sold separately. These items are available at your local Harley-Davidson dealership.

INSTALL

WARNING

Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)

WARNING

Position footpegs so rider can operate foot controls without interference. Failure to have full access to foot controls can cause loss of control, which could result in death or serious injury. (00313a)

WARNING

Mount the footpegs so they will not strike the ground during cornering. Footpegs striking the ground during cornering can cause loss of control, resulting in death or serious injury. (00458c)

WARNING

If footpeg mounting location increases motorcycle width, maintain clearance between motorcycle and surrounding persons or objects. Failure to maintain clearance could result in death or serious injury. (00314a)

NOTE

Mounts are intended to provide an alternative foot position while rider is seated in a normal riding position. Mounts are not intended to be used as lift points, tie downs, steps and the like or for mounting anything other than the appropriate footpegs. Misuse may cause damage to the assemblies, vehicle or rider and will constitute an abuse case of the parts.
Due to vehicle assembly variations and close proximity, vehicles with lower fairings may need to be adjusted to prevent contact and potential paint damage. See service manual.
If clamp position is too low on engine guard, it may contact the ground during cornering. Be aware of when making a decision of final location for the highway peg mount.
It is recommended footpeg be placed in an orientation that folds up and rearward.
With installed variations and footpeg options, some combinations may not meet international regulations for external projections, particularly with the peg folded up. Review options and installation carefully.

1.	See Figure 1. Position footpeg mount (3) and clamp (1) on engine guard.
2.	Kits 50503333, 50503334: See Figure 2. Bracket marked "L" (Part No. 50503215, 50503217) used on left side of vehicle. Brackets marked "R" (Part No. 50503214, 50503216) used on right side of vehicle.
3.	Position footpeg mount (3) to allow footpeg to fasten on inboard side of engine guard. a. See Figure 3 for zone of installation. Mount should be at the highest point of the straight section.
4.	Attach screws (4) to fasten footpeg mount in a comfortable location on engine guard.
5.	Hand tighten each screw.
6.	Alternate between screws when tightening. Tighten. Torque: 27.1 N·m (20 ft-lbs)
7.	Install footpeg, sold separately. a. Position spring washer (2) inside footpeg mount with square edge toward the inside of the mount. b. Secure with clevis pin (5) and retaining ring (6).
8.	Repeat steps 1-6 on the other side of the motorcycle.

1	"L" (left side)
2	"R" (right side)

Figure 2. Left/Right Side Markings

1	Acceptable zone of installation

Figure 3. Acceptable Zone of Installation