SCREAMIN' EAGLE HIGH-FLOW EXHAUST SYSTEM - TOURING
J056292015-03-17
GENERAL
Kit Numbers
64800022, 64800043, 64800044
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
Either Permatex® Anti-Seize Lubricant (Part No. 98960-97) or Loctite® SILVER GRADE Anti-Seize Lubricant (Part No. 11100001) is required for proper installation of this kit.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet refers to service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.
Kit Contents
See Figure 3 and Table 1.
PRODUCT INFORMATION
Tampering Prohibition
Federal law prohibits any modifications to this exhaust system which cause the motorcycle to exceed Federal noise standards. Use of a motorcycle with such a modified exhaust system is also prohibited.
Noise Emission Warranty
Harley-Davidson warrants that these mufflers, at the time of sale, meet all applicable United States E.P.A. Federal Noise and Emissions standards. This warranty extends to the original purchaser for purposes other than resale, and to all subsequent buyers. Direct warranty claims to an authorized Harley-Davidson dealer.
NOTE
To avoid penalties under state and local ordinances, repair or replace this product if motorcycle noise increases significantly through use.
PREPARATION
WARNING
To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
NOTE
  • WITH security siren: With security fob present, turn ignition switch ON. See the service manual. After system is disarmed, turn ignition switch OFF. IMMEDIATELY remove the main fuse.
  • WITHOUT security siren: See the service manual. Remove main fuse.
INSTALLATION
1.
Remove saddlebags per the service manual.
2.
See the service manual. Remove the original equipment (OE) exhaust system. Save exhaust flanges ( Figure 1 , item 3) and mounting hardware for later installation.
3.
See the service manual. Remove oxygen (O2) sensors. Save for installation.
4.
See Figure 2. Remove exhaust bracket (9) at the rear of transmission case (5). Discard bracket and fasteners.
5.
See Figure 1. Remove pipe shields (6 and 7) and clamps (4) from front and rear head pipes. Save pipe shields and clamps for later installation.
6.
Remove collector shield (1). Remove and save clamps (5). Discard collector shield.
7.
See the service manual. Install O2 sensors in new head pipe. Tighten to 16–19 N·m (12–14 ft-lbs).
8.
Apply Anti-Seize Lubricant to O2 sensor plugs (10). Install seal rings (11) and O2 sensor plugs into ARF data monitoring ports. Tighten to 40–60 N·m (30–44 ft-lbs).
9.
See the service manual. Loosely install new head pipe (13).
10.
See Figure 1. Loosely install transmission exhaust bracket bolt (2) and nut (9).
11.
See the service manual and Figure 2. Loosely install new cross-under exhaust pipe (10) and clamp (6).
12.
Verify that the holes of the exhaust pipe bracket align with the mounting holes in the transmission (5). Loosely install new flange screws (9).
13.
See Figure 1. Tighten exhaust manifold nuts (8) to 11.3–13.6 N·m (100–120 in-lbs).
14.
Tighten the transmission exhaust bracket bolt (2) and nut (9) to 27–34 N·m (20–25 ft-lbs).
15.
Check the cross-under exhaust pipe alignment. Verify that the exhaust pipe is not bound or stressed.
16.
See Figure 2. Tighten flange screws (9) to 9.5–14.9 N·m (84–132 in-lbs).
17.
Tighten the cross-under exhaust pipe clamp (6) to 47.5 N·m (35 ft-lbs).
18.
Install new muffler clamps onto mufflers and slide onto headpipes.
19.
See the service manual. Install mufflers (3).
20.
See the service manual. Route and connect O2 sensor wiring.
21.
See Figure 1. Install collector shield (1) using worm drive clamps (5) and (4) removed earlier. Tighten to 2.2–4.5 N·m (20–40 in-lbs).
22.
See Figure 2. Install cross-under exhaust pipe shield (2) using worm drive clamps (1) removed earlier. Tighten to 2.2–4.5 N·m (20–40 in-lbs).
23.
See Figure 1. Install pipe shields (6 and 7) using worm drive clamps (4) removed earlier. Tighten to 2.2–4.5 N·m (20–40 in-lbs).
NOTICE
Wipe all fingerprints off of exhaust system components after installation and before starting engine. Oil from hands can leave permanent marks on exhaust system finish. (00346a)
24.
Wipe exhaust system clean.
COMPLETION
NOTE
Verify that the ignition is OFF before installing the main fuse.
  1. Install main fuse.
  2. Start motorcycle. Check for exhaust leaks.
  3. See the service manual. Install saddlebags.
1 Collector shield
2 Carriage bolt
3 Clamp ring (2)
4 Worm drive clamp (5)
5 Worm drive clamp (2)
6 Pipe shield assembly
7 Pipe shield assembly
8 Flange nut (4)
9 Flange nut
10 Oxygen sensor plug (2)
11 Seal ring (2)
12 Exhaust support bracket
13 Exhaust pipe
Figure 1. Header Pipe Installation
1 Worm drive clamp (2)
2 Pipe shield, cross-under exhaust pipe
3 Muffler (2)
4 Muffler mounting bracket (2)
5 Transmission
6 Muffler clamp
7 Muffler clamp (2)
8 Screw (4)
9 Flange screw (2)
10 Cross-under exhaust pipe
Figure 2. Cross-Under Exhaust Pipe Installation
SERVICE PARTS
Figure 3. Service Parts: Screamin' Eagle High-Flow Exhaust System - Touring
Table 1. Service Parts
Item
Description (Quantity)
Part Number
1
Pipe shield, left (chrome)
Pipe shield, left (black)
65400156
65400229
2
Muffler assembly, disc style (chrome) (2)
Muffler kit, end cap style (left/right, chrome)
Muffler kit, end cap style (left/right, black)
64900203
64900397
64900398
3
Muffler clamp
65900009
4
Muffler clamp (2)
65900010
5
Worm drive clamp
9956
6
Collector shield (chrome)
Collector shield (black)
65400164
65400228
7
Oxygen sensor plug (2)
65835-09
8
Screw, flange
3563
9
Seal ring
27714-06
10
Exhaust pipe, left
64800020
11
Exhaust pipe
Not sold separately
12
Pipe shield kit (black)
64981-09