LIGHTED MIRROR KITS
J058512013-06-07
GENERAL
Kit Number
56000080, 56000081
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
NOTE
The mirrors in this kit are not intended to replace the stock turn signals. Mirror turn signals will not function properly without the stock turn signals installed.
Additional Parts Required
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer.
NOTICE
It is possible to overload your vehicle's charging system by adding too many electrical accessories. If the combined electrical accessories operating at any one time consume more electrical current than the vehicle's charging system can produce, the electrical consumption can discharge the battery and cause damage to the vehicle's electrical system. See an authorized Harley-Davidson dealer for advice about the amount of current consumed by additional electrical accessories or for necessary wiring changes. (00211c)
Kit Contents
See Figure 5 and Table 2.
WARNING
When installing any electrical accessory, be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modified. Exceeding the maximum amperage can lead to electrical failures, which could result in death or serious injury. (00310a)
NOTE
This kit requires up to 500 mA of additional current from the electrical system.
REMOVAL
WARNING
To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
  1. See the service manual. Remove the following:
    1. Left side saddlebag.
    2. Left side cover.
    3. Main fuse.
    4. Outer fairing.
  2. See Figure 1. Remove acorn nut (1), star washer (2) and existing mirror (3) from clutch hand control assembly. Discard star washer and mirror but save acorn nut.
  3. See Figure 2. Repeat previous step for the front brake hand control assembly. Discard star washer and mirror but save acorn nut.
  4. See the service manual. Remove front turn signal/auxiliary lamp assemblies and disconnect the turn signal connectors.
INSTALLATION
1. See Figure 1. Install new mirror stem (1) through clutch hand control assembly.
2. Install stock washer (2) or flat washer from kit (3) on top of hand control assembly (if needed) to stabilize mirror stem.
3. Slide mirror power lead wire (gray) through ground wire ring terminal (5) (flat side up), then install ring terminal on mirror stem.
4. Slide mirror power lead wire (gray) through wire guard (6), then install wire guard on mirror stem.
5. Install flat washer (3) from kit on mirror stem.
NOTE
Be sure wire exiting mirror stem is positioned in wire guard so it does not get crushed by hardware.
6. Install acorn nut (4) on mirror stem (1). Tighten to 10.8–16.3 N·m (8–12 ft-lbs). Do not over-tighten.
7. See Figure 2. Repeat installation steps for front brake hand control assembly.
1Mirror, left
2Washer, flat (stock)
3Washer, flat (from kit)
4Acorn nut
5Ground ring terminal
6Wire guard
Figure 1. Install Left Lighted Mirror
1Mirror, right
2Washer, flat (stock)
3Washer, flat (from kit)
4Acorn nut
5Ground ring terminal
6Wire guard
Figure 2. Install Right Lighted Mirror
8.
Connect Mirrors to Y-Harness
1. See the service manual connector appendix. Assemble Y-harness.
a. See Figure 5. Get the jumper wire (15), pin housing (8), socket housing (9) and dielectric grease (13).
b. Coat the pin and terminal sockets with dielectric grease.
c. See Figure 3 and Table 1. See the service manual connector appendix and install the pin and socket terminations for the Y-harness into the connector housing cavities 1, 2 and 3.
d. Coat the pin and terminal sockets of the jumper wire (2) with dielectric grease.
e. Install the jumper wire into cavity 4 of the socket connector housing (3) and the pin connector housing (4).
1Y-harness wires (blue, red and black)
2Jumper wire (Grey/Black)
3Socket housing
4Pin housing
Figure 3. Y-Harness with Jumper Wire Installed
2. Route the wires of the mirror down to the turn signal connector. Secure the mirror wire with cable straps.
3. See the service manual. Install socket terminals ( Figure 5 , item 4) onto the mirror wires.
4. See the service manual connector appendix. Install socket housing ( Figure 5 , item 7) to mirror wires.
a. Coat the socket terminals with dielectric grease.
b. See Table 1. See the service manual connector appendix and install the mirror wire socket terminals into the connector housing cavities.
5. See Figure 4. Install the Y-harness (3) to the turn signal harness connector.
6. Connect the mirror connector to the Y-harness (3).
7. See the service manual. Connect the turn signal connector (2) to the Y-harness, then install turn signal bracket assembly.
8. Repeat the procedure for the opposite side mirror cover.
Table 1. Wire Color and Cavity Locations
Turn Signal and Mirror Connectors
Cavity
1
2
3
4
4-Place Connector Housings
Blue
Red
Blk
Grey/Blk
1Turn signal harness connector, female
2Turn signal connector, male
3Y-harness
4Mirror cover connector
Figure 4. Auxiliary/Fog Lamp Assembly
Final Assembly
  1. Follow instructions in the service manual for the following procedures:
    1. Outer fairing
    2. Main fuse.
    3. Left side cover.
    4. Left saddlebag.
SERVICE PARTS
Figure 5. Service Parts: Lighted Mirrors
Table 2. Service Parts: Lighted Mirrors
Item
Description (Quantity)
Part Number
1
Lighted mirror, left (with gray lead wire), chrome
92055-07
2
Lighted mirror, right (with gray lead wire), chrome
92056-07
3
Ground wire (2)
Not Sold Separately
4
Terminal, socket (6)
72560-07
5
Y-Harness assembly (2) (includes fuse holder and fuse)
69200811
Fuse, 2 amp blade (2) (not shown)
54305-98
6
Conduit, black (2)
Not Sold Separately
7
Socket housing, 4-way (2)
72907-11
8
Socket housing, 4-way (2)
72908-11
9
Socket housing, 4-way (2)
73152-96BK
10
Wire guard (2)
72561-07
11
Washer, flat (4)
6771A
12
Cable strap (10)
10006
13
Dielectric grease, 4-6 gram packet
Not Sold Separately
14
Locknut, nylon insert 5/16-24 (2) - Sportster, FXSTS, FLSTS models only
7727
15
Jumper wire assembly (2)
56913-06