XG750A BUNGEE BAR KIT
J063872017-08-23
GENERAL
Kit Number
50300123
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
Loctite® 243 (Blue) Threadlocker and Sealant (Part No. 99642-97) is required for proper installation of this kit.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer.
Kit Contents
See Figure 5 and Table 1.
PREPARE
1.
Remove seat. See Service Manual.
2.
Remove rear fender. See Service Manual.
3.
Place rear fender on a suitable surface.
REMOVAL/INSTALLATION
WARNING
Improper loading of cargo or installation of accessories can affect motorcycle stability and handling, which could result in death or serious injury. (00121a)
Use the following guidelines when equipping a motorcycle or carrying passengers and cargo.
  • Keep cargo weight concentrated close to the motorcycle and as low as possible to minimize the change in the motorcycle's center of gravity. Distribute weight evenly and do not load bulky items too far behind the rider or add weight to the handlebars or front forks.
  • Be sure cargo is secure and will not shift while riding. Periodically recheck load.
1.
See Figure 1 From underneath, remove two RH hex head bracket screws (2) and washers (3). Save hardware for installation.
2.
From above, remove two rear fender support bracket bolts and rear fender bracket supports. Discard original bracket support.
3.
Position new rear fender bracket support and install the original hardware hex head screws (2) and washer (3) saved from removal. Tighten.
Torque: 5.3–6.5 N·m (47–58 in-lbs)
4.
See See Figure 2. Position tail rack bungee bar (5) and with new bolts (4), install bungee bars.
5.
NOTE
Hand tighten all new bolts before torquing.
Tighten bolts.
Torque: 20–24 N·m (15–18 ft-lbs)
6.
Repeat steps 1-5 on the LH side.
7.
Install rear fender. See Service Manual.
8.
Place stand under vehicle for support.
9.
Remove rear upper shock bolt and washer. Discard washer.
10.
Clean fastener threads. To attain proper clamp load, always clean fastener threads and threaded holes prior to assembly.
NOTE
Never use a thread-cutting tap or die to clean threads.
a.
Clean all threadlocking material from fastener threads and threaded holes.
b.
Use a wire brush or thread-chasing die to clean fastener threads.
c.
Use a thread chaser to clean threaded holes.
d.
Use PJ1 cleaner or equivalent to remove all traces of oil and contaminants from threads.
e.
Clear all threaded holes with low-pressure compressed air.
f.
Always verify cleanliness of blind holes before assembly. Tightening a screw with dirt, water or oil int he hole can cause castings to crack or break.
11.
See See Figure 3. Apply Loctite to original OE bolt. Install new washer clip and original bolt. Tighten.
Torque: 61–68 N·m (45–50 ft-lbs)
12.
Repeat on opposite side.
13.
See See Figure 4. Install bungee bar license reflector relocation kit. Tighten.
Torque: 1.1–1.7 N·m (10–15 in-lbs)
14.
Install seat. After installing seat, pull up on the seat to verify that it is secure. See Service Manual.
NOTE
Make sure that the tail light is not covered when securing bags on the bungee bar and tail bag.
1Rear license plate bracket
2Hex head bracket screws (4)
3Washers (4)
4Rear fender bracket supports (2)
Figure 1. Rear License Plate Bracket
1License plate bracket
2LH bungee bar
3Bolts (4)
4RH bungee bar
Figure 2. Tail Rack Bungee Bar
1Shock bolt
2Washer clip
Figure 3. Washer Clip
1Nuts (2)
2Washers (6)
3Bungee bar license reflector (2)
4Screws (2)
Figure 4. Bungee Bar License Reflector
SERVICE PARTS
Figure 5. Service Parts: Bungee Bars
Table 1. Service Parts Table
Item
Description (Quantity)
Part Number
1
M8 x 80 Flange bolt (4)
10200180
2
Rear fender support through hole spacer (2)
59500633
3
Left tail rack bungee bar sub assembly
Not sold Separately
4
Tail bracket washer (2)
50300230
5
Right tail rack bungee bar sub assembly
Not sold Separately
6
Bungee bar license reflector relocation kit
67900416