INNER FAIRING KIT
J057732013-08-15
GENERAL
Kit Number
57000387xxx, 57000388xxx, 57000389xxx, 57000398, 57000399, 57000400
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Service Manual Required
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references Service Manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer.
Kit Contents
See Figure 3 and Table 1.
INSTALLATION
  1. Unpainted kits: See Figure 1. After painting, install foam tape pieces to inner surface around radio opening:
    1. Install upper foam (1) touching guide ribs (4).
    2. Install side foam pieces (2) as shown.
    3. Install lower foam (3) at guide lines (5).
1Foam tape, 0.38 x 0.50 x 8.5 in
2Foam tape, 0.31 x 0.25 x 1.15 in (2)
3Foam tape, 0.38 x 0.13 x 8.0 in
4Guide ribs
5Guide lines
Figure 1. Foam Tape Locations: Inner Fairing
1.
Remove the inner fairing. See INNER FAIRING, Inner Fairing Assembly Removal and Installation in the service manual.
NOTE
  • Label mirror location prior to removal to ease installation.
  • FLHX/S models: See Figure 2. The letters "L" or "R" are stamped on the backing plate and inner fairing to identify mirror location.
Figure 2. Mirror Location Mark
2.
Transfer all components from the original inner fairing. See INNER FAIRING, Inner Fairing Shell Replacement in the service manual.
3.
See Figure 3. Install new cover (4) and gasket (5) on media compartment door. See INNER FAIRING, Media Compartment in the service manual.
4.
Transfer switch modules to the new dash panel (6). See DASH PANEL SWITCHES in the service manual.
5.
FLHX/S models: Install three plugs (7) on each side.
6.
Install the inner fairing, outer fairing and windshield. See INNER FAIRING, Inner Fairing Assembly Removal and Installation in the service manual.
7.
Adjust the mirrors for proper field of vision and compliance with local regulations.
SERVICE PARTS
Figure 3. Service Parts: Inner Fairing Kit
Table 1. Service Parts Table
Item
Description (Quantity)
Part Number
1
Inner fairing
not serviced separately
2
Edge trim, right
61400064
3
Edge trim, left
61400063
4
Cover, media compartment door, painted (Kits 57000387xxx, 57000388xxx, 57000389xxx)
76000409xxx
Cover, media compartment door, unpainted (Kits 57000398, 57000399, 57000400)
76000110
5
Gasket, media compartment door
76000234
6
Dash panel, painted (Kits 57000387xxx, 57000388xxx, 57000389xxx)
70900392xxx
Dash panel, unpainted (Kits 57000398, 57000399, 57000400)
70900137
7
Plug (6) (Kits 57000400, 57000389xxx)
12100034
8
Foam tape, 0.38 x 0.50 x 8.5 in
11100050
9
Foam tape, 0.31 x 0.25 x 1.15 in (2)
11100057
10
Foam tape, 0.38 x 0.13 x 8.0 in
11100051