TOUR-PAK RACK LIGHT KIT
J058472013-06-01
GENERAL
Kit Number
68000112, 68000113
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Additional Parts Required
Separate purchase and installation of additional parts or accessories may be required for proper installation of this kit on your model motorcycle. See the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only) for a list of required parts or accessories for your model.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer.
Kit Contents
See Figure 3 and Table 1.
INSTALLATION
1.
Remove all contents from Tour-Pak®.
NOTE
Remove Tour-Pak rack for easier installation. Follow instructions in service manual.
2.
See Figure 1. Remove rubber plug (1) from bottom rear rail on left side of rack.
3.
Use line wire feeder in kit to thread through left rear rack foot (2) and out through the back opening of rail.
4.
Attach light harness wires to line wire feeder loop.
5.
Carefully pull line wire feeder and light harness wires through rack mounting foot.
1Plug
2Rear rack foot
Figure 1. Rack Plug and Foot
6.
See Figure 3 and Table 1. Apply foam pads (5) to top surface of light.
7.
Secure light (1) to rack with socket head screws (4) and washers (6).
8.
Position rack/light assembly to Tour-Pak lid and route wires through lid, washer and hollow mounting bolt.
9.
Attach rack/light assembly to Tour-Pak using instructions and hardware provided with rack except for use of hollow bolt from previous step.
10.
Remove Tour-Pak liner following directions in service manual.
11.
Thread wires through black vinyl conduit.
12.
See Figure 2. Connect light assembly connector to rear lighting connector (1).
13.
Remove grommet (2) from Tour-Pak.
14.
Route Y-harness wires through hole in Tour-Pack.
15.
Install new grommet around all wires and install in Tour-Pak.
1Rear lighting connector
2Grommet
Figure 2. Tour-Pak Lighting Connector
16.
See Figure 3. Refer to the Service Manual electrical appendix to install terminal pins (8) to rack light wires and install terminals to three pin housing (7) as follows:
  • #1 cavity = blue lead
  • #2 cavity = red with yellow lead
  • #3 cavity = black lead
NOTE
To prevent corrosion, fill the cavities of the connectors with dielectric grease (included in kit) prior to making connections.
As an additional precaution against moisture seepage into the Tour-Pak, apply silicone sealant (not included in kit) to the entrance of the light harness wire tunnel.
  1. Replace Tour-Pak liner following directions in service manual.
  2. Check operation of Tour-Pak tail and stop light functions before operating motorcycle.
SERVICE PARTS
Figure 3. Service Parts: Tour-Pak Rack Light Kit
Table 1. Service Parts Table
Item
Description (Quantity)
Part Number
1
LED light assembly
Not Sold Separately
2
Auxiliary wiring harness
Not Sold Separately
3
Dielectric grease (not shown)
Not Sold Separately
4
Socket head screw, 8-32, stainless steel (2)
Not Sold Separately
5
Pad (2)
Not Sold Separately
6
Flat washer, 0.172 x 0.375 x 0.035, stainless steel (2)
Not Sold Separately
7
Pin housing, 3 place
73103-96BK
8
Pin terminal, 16-20 AWG (3)
73190-96
9
Grommet
10100055
10
Cable strap (4)
10006
11
Clip, adhesive backed (4)
10102
12
Conduit, 42 inches long (not shown)
Not Sold Separately
13
Wire guide, nylon monofilament (not shown)
Not Sold Separately