BRAWLER STYLE SEAT KITS
J066152018-01-16
GENERAL
Kit Number
52000299, 52000301
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
Kit Contents
Refer to Figure 5 and Table 1.
INSTALLATION
NOTE
When performing the following installation procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs.
1.
Remove seat and seat studs, if equipped. See service manual.
2.
Remove rear fender protective tape, if equipped.
3.
Refer to Figure 1 and Figure 2. Install retention nut (1) and washer (2) in the appropriate fender hole if not already installed.
a.
A cable strap may be used as an installation aid to install the retention nut and washer. Place the retention nut (1) over the cable strap (3) so the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender and through the appropriate fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender.
b.
With the rib on the retention nut seated into the notch in the appropriate fender hole, slide the retention washer (2) into place from the rear. This will lock the retention nut in place. Remove the cable strap.
c.
See Figure 5. Install seat post (5) on washer (6) and retention washer (7) over retention nut (9). Tighten.
Torque: 2.25–3.38 N·m (20–30 in-lbs)
4.
See Figure 5. Mark and apply protective tape to fender.
a.
Mark the bottom of isolators (3) that contact the fender with chalk.
b.
Set the seat in place with front and rear mounting locations on the seat aligned with the mounting locations on the motorcycle.
c.
Press down on the seat to transfer the marks from the isolators to the fender.
d.
Place protective tape (8) on the rear fender over the marks transferred to the fender.
5.
Install Seat.
NOTE
This seat is for solo use only. Do not attempt to carry a passenger with this custom solo seat installed.
a.
Refer to Figure 3 and Figure 4. Engage seat tongue (B) in seat mounting bracket (A).
b.
Align seat grommet (2) on seat post (5) and push down on seat until you hear a click.
6.
After installing seat, pull up on the seat to verify it is secure.
7.
Models equipped with passenger footpegs, remove footpegs.
1Retention nut
2Retention washer
3Cable strap
Figure 1. Installation Tool
Figure 2. Fitment Location
Figure 3. Seat Tongue (typical)
Figure 4. Seat Mounting Bracket
SERVICE PARTS
Figure 5. Service Parts: Softail Seat Kits
Table 1. Service Parts Table
Kit
Item
Description (Quantity)
Part Number
52000299, 52000301
1
Seat assembly
Not sold separately
Seat assembly
Not sold separately
2
Grommet
11651
3
Seat isolator (11)
11100174
4
Badge
Not sold separately
5
Post
52100051
6
Washer
10300163
7
Retention washer (part of seat nut kit)
Not sold separately
8
Protective tape (4)
11100176
9
Retention nut (part of seat nut kit)
Not sold separately
Seat nut kit (includes items 6 and 9)
59768-97
10
Cable strap
10039
Items mention in text:
A
Seat mounting bracket
B
Seat tongue