0/0
VRSCDX LUGGAGE RACK AND BACKREST
J053732013-04-02
GENERAL
Kit Number
50300028, 52300016
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Additional Parts Required
If the backrest is being installed after previous luggage rack installation, then proper installation requires the use of Loctite® 243 Threadlocker and Sealant - Blue (Part No. 99642-97).
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer.
Kit Contents
See Figure 5 and Table 1.
INSTALLATION
Prepare Fender Cover
WARNING
To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
1. See the owner's manual and remove the main fuse.
2. See the service manual and remove the rear fender cover.
3. See Figure 1. Place masking tape over the three drill points to prevent the paint from chipping when the holes are drilled.
4. See Figure 2. Turn the fender cover over and place it on a clean, soft cloth on a bench.
CAUTION
Always wear proper eye protection when drilling or grinding. Flying debris could cause serious eye injury. (00402e)
5. Drill three pilot holes through the three mounting points using a 3.5 mm (⅛ in) drill bit.
6. Turn the fender cover over and drill three 6.25 mm (¼ in) holes in the pilot hole locations. The holes will not be perpendicular to the work surface. Be careful to follow the path of the pilot holes, so the kit will align properly.
7. Remove tape.
1Masking tape
2Outer fender
Figure 1. Apply Masking Tape to Outer Fender
1Drill point (3)
Figure 2. Outer Fender Drill Points
Install Luggage Rack Only
NOTE
Only loosely install hardware, when installing the base plate and luggage rack to the fender. The hardware will be tightened at the end of the procedure.
1. Set the luggage rack upside down on the edge of a workbench.
2. See Figure 3. Install the base plate (2) over the luggage rack (1).
3. See Figure 5. To align the components, start the forward two screws (12) through the base plate and luggage rack just enough for the screw threads to engage.
4. Install screw (10) through the base plate and luggage rack. Tighten screw to 9 N·m (80 in-lbs).
5. Remove two screws (12).
6. Install the fender cover over the luggage rack assembly and align the drilled holes in the cover with the mounting holes in the base plate.
7. Install three screws (12) and washers (11) as follows:
a. Start the two forward mounting screws.
b. Start the rear, center mounting screw. If the hole does not align properly, use a drill to enlarge the hole slightly and improve alignment.
c. Tighten screws to 9 N·m (80 in-lbs).
8. See the service manual and install the fender cover with the mounted backrest and luggage rack assembly.
9. See the owners manual and install the main fuse.
1Luggage rack
2Base plate
Figure 3. Luggage Rack Only Installation
Install Backrest and Luggage Rack
NOTE
If installing the backrest after previously installing the luggage rack only, remove the fender cover, luggage rack and base plate from the motorcycle. Follow the directions below for installing the kit. Clean screws (items 10 and 12, Figure 5 ) and use Loctite 243 - blue for re-installation.
Only loosely install hardware, when installing the base plate, backrest and luggage rack to the fender. The hardware will be tightened at the end of the procedure.
1. Set the luggage rack upside down on the edge of a workbench.
1Luggage rack
2Base plate
3Backrest
Figure 4. Luggage Rack and Backrest Installation
2. See Figure 4. Orient the backrest (3) so that the outer mounting holes of the backrest align with the mounting holes of the luggage rack (1).
3. Install the base plate (2) over the backrest and luggage rack.
4. See Figure 5. Start screw (3) and washer (2).
5. Align the components, start the forward two screws (12) through the base plate and luggage rack enough for the screw threads to engage.
6. Start screw (10) through the base, backrest and luggage rack.
7. Tighten screw (3) to 12 N·m (106 in-lbs).
8. Tighten screw (10) to 9 N·m (80 in-lbs).
9. Remove two screws (12).
10. Install the fender cover over the backrest and luggage rack assembly and align the drilled holes in the cover with the mounting holes in the base plate.
11. Install three screws (12) and washers (11) as follows:
a. Start the two forward mounting screws.
b. Start the rear, center mounting screw. If the hole does not align properly, use a drill to enlarge the hole slightly and improve alignment.
c. Tighten screws to 9 N·m (80 in-lbs).
12. See the service manual and install the fender cover with the mounted backrest and luggage rack assembly.
13. See the owners manual and install the main fuse.
SERVICE PARTS
Figure 5. Service Parts: VRSCDX Luggage Rack and Upright
Table 1. Service Parts
Item
Description (Quantity)
Part Number
Backrest kit
(includes items 1 through 7)
52300016
1
  • Backrest
Not Sold Separately
2
  • Washer
Not Sold Separately
3
  • Screw, M6 x 1.0 x 10 mm
Not Sold Separately
4
  • Pad, front
52300062
5
  • Pad, rear, right
52300063
6
  • Pad, rear, left
52300064
7
  • Screw, stainless, M4 x 0.7 (4) (Not Shown)
Not Sold Separately
Luggage rack kit
(includes items 8 through 12)
50300028
8
  • Luggage rack
53319-09
9
  • Base plate
Not Sold Separately
10
  • Screw, M6 x 1.0 x 25 mm
Not Sold Separately
11
  • Washer, M6 (3)
Not Sold Separately
12
  • Screw, M6 x 1.0 x 45 mm (3)
Not Sold Separately
Items mentioned in text, but not included in kit.
A
Fender cover