0/0
CUSTOM HAND LEVER KITS
J057202013-06-01
GENERAL
Kit Numbers
36700067, 36700066, 36700065, 36700064, 36700091
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Tools and Supplies Required
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer.
WARNING
Brakes are a critical safety component. Contact a Harley-Davidson dealer for brake repair or replacement. Improperly serviced brakes can adversely affect brake performance, which could result in death or serious injury. (00054a)
Kit Contents
See Figure 1 and Table 1.
BRAKE LEVER INSTALLATION
WARNING
Contact with DOT 4 brake fluid can have serious health effects. Failure to wear proper skin and eye protection could result in death or serious injury.
  • If inhaled: Keep calm, remove to fresh air, seek medical attention.
  • If on skin: Remove contaminated clothing. Rinse skin immediately with plenty of water for 15-20 minutes. If irritation develops, seek medical attention.
  • If in eyes: Wash affected eyes for at least 15 minutes under running water with eye lids held open. If irritation develops, seek medical attention.
  • If swallowed: Rinse mouth and then drink plenty of water. Do not induce vomiting. Contact Poison Control. Immediate medical attention required.
  • See Safety Data Sheet (SDS) for more details available at sds.harley-davidson.com
(00240e)
NOTICE
DOT 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239c)
NOTE
Immediately wipe up any brake fluid spillage with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills).
Cover nearby motorcycle surfaces with a polyethylene protective sheeting to help protect against damage to finish caused by spillage or splash of D.O.T. 4 brake fluid.
  1. Remove stock brake lever following instructions in the service manual.
  2. Install new brake lever following instructions in the service manual.
CLUTCH LEVER INSTALLATION
See the CLUTCH CONTROL section of the Service Manual for clutch lever (8) removal, installation and adjustment procedures.
SERVICE PARTS
Figure 1. Service Parts: Hand Control Lever (Slotted Shown)
Table 1. Service Parts: Hand Control Lever Kits
Kit
Item
Description (Quantity)
Part Number
Kit 36700065
Chrome Levers
1
Brake hand lever, chrome (includes Items 3 through 7)
Not Sold Separately
2
Clutch hand lever, chrome (includes Items 8 through 11, 13)
Not Sold Separately
Kit 36700064
Black Levers
1
Brake hand lever, black (includes Items 3 through 7)
Not Sold Separately
2
Clutch hand lever, black (includes Items 8 through 11, 12)
Not Sold Separately
Kit 36700066
Slotted Levers
1
Brake hand lever, slotted (includes Items 3 through 7)
Not Sold Separately
2
Clutch hand lever, slotted (includes Items 8 through 11)
Not Sold Separately
Kit 36700067
Edge Cut Levers
1
Brake hand lever, slotted (includes Items 3 through 7)
Not Sold Separately
2
Clutch hand lever, slotted (includes Items 8 through 11, 12)
Not Sold Separately
Kit 36700091
Chrome Levers
1
Brake hand lever, slotted (includes Items 3 through 7)
Not Sold Separately
2
Clutch hand lever, slotted (includes Items 8 through 11)
Not Sold Separately
Parts common
to ALL Kits
3
Brake hand lever (includes Item 4)
Not sold separately
4
  • Bushing, brake lever pivot
Not sold separately
5
Pivot pin kit (polished). For all Kits EXCEPT 36700064 (includes Items 6 and 7)
Pivot pin kit (black). For Kit 36700064 (includes Items 6 and 7)
42105-06A
42860-06B
6
  • Pivot pin, brake lever
Not sold separately
7
  • Retaining ring
11615
8
Clutch hand lever
Not sold separately
9
Bushing
Not Sold Separately
10
Bushing and Roller Kit
46246-01
11
Retaining ring
11143
12
Pivot pin, black
38738-08
13
Pivot pin, stainless steel
45032-82
Reference items not included in kit:
A
Front brake master cylinder
B
Clutch master cylinder