0/0
FRONT ENFORCER WHEELS
J058672014-09-17
GENERAL
WARNING
Install only wheels and installation kits approved for your model motorcycle. Contact a Harley-Davidson dealer to verify fitment. Mismatching wheels and installation kits or installing wheels not approved for your model can cause loss of control, which could result in death or serious injury. (00610c)
Kit Number
43300336, 43300324
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
NOTE
Accessory hub caps are not compatible with this wheel.
Kit Contents
See Service Parts for kit contents.
Installation Requirements
Proper installation of this kit requires the separate purchase of the following parts which are available at a Harley-Davidson dealer:
Wheel Installation Kit (See Table 1 and Table 2 to determine required installation kit.)
For Kit 43300336:
  • 2 Brake Discs: stock/raw (41500017) or accessory/polished (41500094)
  • 10 Brake disc screws (41500020), washers (41500019), and bushings (41500018) or 2 chrome screw kits 41500095 (hardware already included in polished rotor kit - 41500094)
For Kit 43300324:
  • 2 Brake Discs: stock/raw (41500068), accessory/polished (41500107), or see the P&A Retail Catalog.
  • 10 Brake disc screws (3655A) or 2 chrome screw kits (46646-05) (hardware already included in polished rotor kits)
Wheel Bearing Remover and Installer (94134-09)
The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning:
  • Chrome Clean & Shine (93600031 (US) / 93600082 (International))
  • Glaze Poly Sealant (93600026 (US) / 93600079 (International))
  • Harley® Wheel and Spoke Brush (43078-99)
  • Wheel & Tire Cleaner (93600024 (US) / 93600076 (International))
  • Harley® Preserve Bare Aluminum Protectant (99845-07)
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer.
INSTALLATION
1. Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual.
NOTE
Install pull thru valve stem (40999-87) included in the installation kit. Discard all other valve stems.
NOTICE
Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c)
2. See Figure 1. Install valve stem assembly (N) on wheel. Refer to TIRES in service manual.
NOTE
The bearing shims provided in the installation kits are not required and can be discarded.
3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in service manual.
NOTE
Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER.
  • The left side of the wheel has DOT markings to identify the primary bearing side.
4. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual.
MAINTENANCE AND CLEANING
Chrome parts must be maintained regularly so that they keep their original shine and luster.
  1. Clean heavily-soiled wheel surfaces using Wheel & Tire Cleaner, applied with Harley Wheel and Spoke Brush.
  2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Chrome Clean & Shine.
  3. After cleaning and polishing, seal the finish with a good quality sealer, such as Glaze Poly Sealant.
SERVICE PARTS
Figure 1. Service Parts: FRONT ENFORCER WHEELS, Kit 43300336 shown.
Table 1. FRONT 25 mm Bearing Wheel Installation Kit (41455-08C)
FRONT 25 mm Bearing Wheel Installation Kit (41455-08C)
ITEM (Quantity Used and Description)
Fitment
Wheel Size
A
C
D
J
K
L
M
N
2008 Touring; 2009 and later FLHRC (non-ABS) and Trike (non-ABS)
16 x 3.0 in
2
0
1
0
**
*
*
*
2009 and later Touring (non-ABS)
17 x 3.0 in
2
0
1
0
0
*
*
*
2008 and later Touring (non-ABS)
18 x 3.5 in
2
0
1
0
**
*
*
*
2008 and later Dyna (except FLD, FXDWG and FXDF)
19 x 2.5 in
2
1
0
**
0
*
*
0
2008 and later VRSCAW, VRSCD, VRSCF and VRSCDX (non-ABS)
19 x 3.0 in
2
1
0
**
0
*
*
0
2009 and later Touring (non-ABS)
19 x 3.5 in
2
0
1
0
0
*
*
*
Installation kits are designed to work with many different wheel styles and fitments. Contact a Harley-Davidson dealer to verify that the wheel and installation kits are both designed and approved for the motorcycle they are being installed on.
NOTES:
* See NOTE above valve installation step in INSTALLATION to determine which valve stem to use for your particular kit. Discard other valve stem(s).
** See NOTES for your wheel kit above the wheel assembly step in INSTALLATION to determine if bearing shim is used for your particular wheel kit and fitment.
*** Bearing shim installed under the primary bearing.
A
Bearing, regular (2)
9276A
C
Axle sleeve
41748-08
D
Axle sleeve
41900-08
J
Bearing shim***
41450-08
K
Bearing shim***
43903-08
L
Valve stem, short
43157-83A
M
Valve stem, long
43206-01
N
Valve stem, pull thru
40999-87
Table 2. FRONT 25 mm Bearing ABS Wheel Installation Kit (41454-08B)
FRONT 25 mm Bearing ABS Wheel Installation Kit (41454-08B)
ITEM (Quantity Used and Description)
Fitment
Wheel Size
A
B
C
D
J
K
L
M
N
2008 Touring and 2009 and later FLHRC with ABS
16 x 3.0 in
1
1
0
1
0
**
*
*
0
2009 and later Touring with ABS
17 x 3.0 in
1
1
0
1
0
0
*
*
*
2008 and later Touring with ABS
18 x 3.5 in
1
1
0
1
**
**
*
*
*
2012 and later Dyna with ABS (Except FLD, FXDWG and FXDF)
19 x 2.5 in
1
1
1
0
**
0
*
*
0
2008 and later VRSCAW, VRSCD, VRSCF and VRSCDX with ABS
19 x 3.0 in
1
1
1
0
**
**
*
*
0
2009 and later Touring with ABS
19 x 3.5 in
1
1
0
1
0
0
*
*
*
Installation kits are designed to work with many different wheel styles and fitments. Contact a Harley-Davidson dealer to verify that the wheel and installation kits are both designed and approved for the motorcycle they are being installed on.
NOTES:
* See NOTE above valve installation step in INSTALLATION to determine which valve stem to use for your particular kit. Discard other valve stem(s).
** See NOTES for your wheel kit above the wheel assembly step in INSTALLATION to determine which bearing shim to use for your particular wheel kit and fitment.
*** Red side of bearing must be installed toward the wheel. The ABS bearing is primary.
**** Bearing shim installed under the primary bearing.
A
Bearing, regular
9276A
B
Bearing, ABS***
9252
C
Axle sleeve
41748-08
D
Axle sleeve
41900-08
J
Bearing shim****
41450-08
K
Bearing shim****
43903-08
L
Valve stem, short
43157-83A
M
Valve stem, long
43206-01
N
Valve stem, pull thru
40999-87