0/0
AUXILIARY BRAKE/ RUN/ TURN SIGNAL CONVERSION KIT
J059672014-02-03
GENERAL
Kit Number
69200765A
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
NOTE
Red turn signal lenses are not legal in all jurisdictions. Check regulations.
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet refers to service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.
Electrical Overload
NOTICE
It is possible to overload the vehicle's charging system by adding too many electrical accessories. If the combined electrical accessories operating at any one time consume more electrical current than the vehicle's charging system can produce, the electrical consumption can discharge the battery and cause damage to the vehicle's electrical system. (00211d)
WARNING
When installing any electrical accessory, be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modified. Exceeding the maximum amperage can lead to electrical failures, which could result in death or serious injury. (00310a)
This kit requires up to 4.5 amps more current from the brake lamp circuit while brakes are applied.
Kit Contents
See Figure 2 and Table 1.
PREPARATION
See the service manual to remove the seat and left side cover. Retain the side cover, seat and all mounting hardware.
Vehicles WITHOUT Security Siren
WARNING
To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
  1. See the service manual to remove the main fuse.
Vehicles WITH Security Siren
  1. With security fob present, turn ignition switch ON. After system is disarmed, turn ignition switch OFF. IMMEDIATELY remove the main fuse per the service manual. See the warning under Vehicles WITHOUT security siren, earlier in this section.
  2. Turn the ignition switch OFF unless already done.
INSTALLATION
  1. See Figure 1. Unplug the right (2) and left (3) four-way Multilock turn signal connector halves [18] and [19] in the area under the seat. Unplug the three-way Multilock tail lamp connector halves [40] (4).
  2. See Figure 2. Get the turn signal module (1) from the kit.
  • Plug the turn signal module four-way connectors with no tape flags (A) into the brown-tape flagged turn signal connector halves [18] on the main vehicle harness and right turn signal wires.
  • Plug the turn signal module four-way connectors with white tape flags (B) into the unflagged turn signal connector halves [19] on the main vehicle harness and left turn signal wires.
  • Plug the turn signal module three-way connectors (C) into the main vehicle harness and tail lamp connector halves [40].
NOTE
Select a location to secure the module:
  • Make sure that connectors and module are not bound when the seat is reinstalled.
  • Make sure that wiring is not pinched when the seat is reinstalled.
  1. Use cable straps (3) from the kit to secure the module, connector and wiring in the area underneath the seat.
  2. Locate the notch in the original amber turn signal lens. Insert a coin or a flat-blade screwdriver into the notch. Carefully twist the coin or screwdriver until the lens pops out of the rear turn signal housing. Repeat for the other rear turn signal lens.
  3. Obtain the red turn signal lenses (2) from the kit. Snap a red lens into the turn signal housing. Repeat for other lens.
1Main vehicle harness
2Right turn signal connector [18]
3Left turn signal connector [19]
4Tail lamp connector [40]
Figure 1. Rear Lighting Connectors Under Seat
COMPLETION
NOTE
Verify that ignition switch is OFF before installing main fuse.
1. See the service manual to install the main fuse.
WARNING
Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a)
2. Turn the ignition switch ON, but do not start the motorcycle. Check for proper lamp function:
  • With ignition switch ON, the left and right turn signal lamps and the center tail lamp are illuminated.
  • With brake lever or brake pedal actuation, the left and right turn signal lamps and the center tail lamp brightens.
  • With left or right turn signal actuation, the correct vehicle turn signal flashes.
  • With hazard warning (emergency four-way flasher) actuation, both turn signals flash.
WARNING
After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b)
  1. See service manual to install seat. Install left side cover.
SERVICE PARTS
Figure 2. Service Parts, Auxiliary Brake/ Run/ Turn Signal Conversion Kit
Table 1. Service Parts
Item
Description (Quantity)
Part Number
1
Auxiliary brake/ run/ turn signal module
Not Sold Separately
2
Lens, turn signal (red) (2)
68217-00
3
Cable strap (3)
10006
Items mentioned in text.
A
No flag (2)
B
White flag (2)
C
Three-way connector (2)