PREMIUM SUSPENSION FOR XL - TALL
J060422016-09-01
GENERAL
Kit Number
54000076
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
This kit requires LOCTITE® 243 (blue) for proper installation.
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.
REMOVAL
NOTE
When removing shocks, remove and replace one shock at a time. This method does not require raising and blocking the rear wheel. To remove both shocks at the same time, place the motorcycle on a center stand with the rear wheel raised off the ground.
- See the service manual. Remove rear shock absorbers. Retain the nuts and washers for new shock installation.
INSTALLATION
| 1. | See Figure 1. Loosely install upper shock mounting bolt (3) to Both Sides: Position the bushing (2) facing the inboard side. Install upper shock eye to frame: | |
| 2. | Install lower shock eye to Right Side (except Japan models): a. Verify bushing (2) is toward vehicle. b. Slide lower mounting bolt (7) through washer (8) and bottom shock eye. c. Slide lower mounting bolt through rear fork. d. Slide lower mounting bolt through one special washer (6). e. Slide lower mounting bolt through the belt guard. f. Slide lower mounting bolt through one special washer (6). g. Apply Loctite 243 (blue) to lower shock bolt. Install nut (4). h. Tighten shock mounting bolt and nut. Torque: 61–68 N·m (45–50 ft-lbs) Nut (4), bolt (7) | |
| 3. | NOTE The lower right side mounting bolt on Japan models must be inserted from inside the rear fork (Opposite of what is shown in Figure 1 ). Removal and installation of rear wheel is needed for this step. a. See the service manual. Remove rear wheel. b. Verify bushing (2) is toward vehicle. c. Slide lower mounting bolt (7) through one special washer (6). d. Slide lower mounting bolt through the belt guard. e. Slide lower mounting bolt through one special washer (6). f. Slide lower mounting bolt through rear fork. g. Slide lower mounting bolt through bottom shock eye and washer (8). h. Apply Loctite 243 (blue) to lower shock bolt. Install nut (4). i. Tighten shock mounting bolt and nut. Torque: 61–68 N·m (45–50 ft-lbs) Nut (4), bolt (7) j. See the service manual. Install rear wheel. | |
| 4. | Remove upper shock bolt. Apply Loctite 243 (blue) to upper shock bolt. | |
| 5. | Slide upper mounting bolt (3) through washer (9) and upper shock eye. | |
| 6. | Slide upper mounting bolt into frame boss. | |
| 7. | Tighten shock mounting bolt. Torque: 61–68 N·m (45–50 ft-lbs) Bolt (3) | |
| 8. | Install lower shock mount to left side: a. Verify bushing (2) is toward vehicle. b. Slide lower mounting bolt (5) through washer (8) and bottom shock eye. c. Slide lower mounting bolt through rear fork. d. Apply Loctite 243 (blue) to lower shock bolt. Install nut (4). e. Tighten shock mounting bolt and nut. Torque: 61–68 N·m (45–50 ft-lbs) Nut (4), bolt (5) | |
| 9. | Remove upper shock bolt. Apply Loctite 243 (blue) to upper shock bolt. | |
| 10. | Slide upper mounting bolt (3) through washer (9) and upper shock eye. | |
| 11. | Slide upper mounting bolt into frame boss. | |
| 12. | Tighten shock mounting bolt. Torque: 61–68 N·m (45–50 ft-lbs) Bolt (3) |
| 1 | Shock absorber |
| 2 | Bushing |
| 3 | Screw, button head, torx, 1/2 x 2-1/2 (2) |
| 4 | Nuts (2) |
| 5 | Screw, button head, torx, 1/2 x 2-9/16 |
| 6 | Washer, special (2) |
| 7 | Screw, button head, torx, 1/2 x 2-7/8 |
| 8 | Washer, 1 in (2) |
| 9 | Washer, 7/8 in (2) |
Figure 1. Rear Shock Absorber Installation
SERVICE PARTS
Figure 2. Service Parts: XL Rear Shock Kit
Table 1. Service Parts
Item | Description (Quantity) | Part Number |
|---|---|---|
1 | Spanner wrench | 14900080 |
2 | Screw, button head, Torx, 1/2 x 2-1/2 (2) | 10200392 |
3 | Shock absorber (2) | 54000086 |
4 | Screw, button head, Torx, 1/2 x 2-7/8 (1) | 10200445 |
5 | Washer, special (2) | 10600039 |
6 | Screw, button head, Torx, 1/2 x 2-9/16 (1) | 4354 |
SHOCK ABSORBER ADJUSTMENT
WARNINGAdjust both shock absorbers equally. Improper adjustment can adversely affect stability and handling, which could result in death or serious injury. (00036b)
NOTE
The locknut is not tight on new shock. The adjustment must be completed and the adjuster nut locked before vehicle operation.
NOTE
To prevent damage to the adjustment and locking rings, do not use any other wrench than the one supplied with this kit.
NOTICE
Avoid shock damage. Make sure shock threads are clean and free of debris before loosening or tightening shock adjusting nuts. (00646b)
- See Table 2. Determine desired upper locking ring location for the total weight of rider, passenger cargo and accessories.
- Clean the adjuster threads.
- See Figure 3. Use the spanner wrench to turn the upper locking ring counterclockwise (1) to unlock the ring:
- Use the spanner wrench to turn (2) the lower adjustment ring below the recommended dot.
- Rotate the upper locking ring to align with the recommended preload dot (3).
- Cover one-half the recommended preload dot (4) with the upper locking ring.
- Use the wrench to hand tighten the lower adjustment ring against the locking ring (5)
- Repeat Shock Absorber Adjustment steps on other side.
- Verify that both shocks are adjusted evenly.
NOTE
Count down from the top of the shock to locate the recommended preload dot.
| 1 | Loosen locking ring |
| 2 | Turn adjustment ring below recommended dot |
| 3 | Rotate locking ring to dot |
| 4 | Align locking ring to dot |
| 5 | Tighten adjustment ring |
Figure 3. Preload Adjustment
Table 2. Tall Travel Shocks Preload
WEIGHT OF PASSENGER, CARGO AND ACCESSORIES | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
lb | 0 | 18 | 36 | 54 | 72 | 90 | 108 | 126 | 144 | 162 | 180 | 198 | 216 | 234 | |
kg | 0 | 8.2 | 16.3 | 24.5 | 32.7 | 40.8 | 49.0 | 57.2 | 65.3 | 73.5 | 81.6 | 89.8 | 98.0 | 106.1 | |
RIDER WEIGHT | PRELOAD DOT | ||||||||||||||
lb | kg | ||||||||||||||
116-141 | 52.6-64.0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 11 | 12 | 13 |
142-167 | 64.4-75.7 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 11 | 12 | 13 | - |
168-193 | 76.2-87.5 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 11 | 12 | 13 | - | - |
194-219 | 88.0-99.3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 11 | 12 | 13 | - | - | - |