HAND GRIPS

941000292023-10-20

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
56100402, 56100445, 56100446, 56100448, 56100449, 56100462, 56100477	Safety Glasses, Torque Wrench

(1) Tightening to torque value or other moderate tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Hand Grips (Typical)

Table 2. Kit Contents: Hand Grips

Verify that all contents are present in the kit before installing or removing items from vehicle.
Item	Qty	Description	Part No.	Notes
1	1	Grip, left, Kit 56100402, black	56100406
		Grip, left, Kit 56100448, black and orange	56100452
		Grip, left, Kit 56100449, gray	56100453
		Grip, left, Kit 56100462, black	56100461
		Grip, left, Kit 56100477, black	56100493
		Grip, left, Kit 56100445, edge cut	56100441
		Grip, left, Kit 56100446, black	56100440
2	1	Grip, right, Kit 56100402, black	56100405
		Grip, right, Kit 56100448, black and orange	56100450
		Grip, right, Kit 56100449, gray	56100451
		Grip, right, Kit 56100462, black	56100460
		Grip, right, Kit 56100477, black	56100494
		Grip, right, Kit 56100445, edge cut	56100444
		Grip, right, Kit 56100446, black	56100443

GENERAL

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

Kit 56100462: End cap (p/n 55801095) quantity of (2) is required

WARNING

Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)

NOTE

This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:

A Harley-Davidson dealer.
H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.

REMOVE

Left

1.	Figure 2 Remove end cap (1).
2.	Remove hand grip (2). a. Loosen clamp screw (3). b. Remove grip.

Right

1.	Remove end cap (1).
2.	Figure 3 Remove rear cover (3).
3.	Remove grip. See service manual.

INSTALL

NOTE

When routing and closing Right and Left Hand Control Modules (R&LHCMs), verify there are no pinched wires. See service manual.

Left

NOTE

Kit 56100462, use end caps (p/n 55801095).

1.	Figure 2 Install hand grip. a. Place grip (2) in position. b. Tighten clamp screw (3). Torque: 4.4–4.8 N·m (39–42 in-lbs)
2.	Install end cap (1). Tighten. Torque: 14–20 N·m (124–177 in-lbs)

Right

1.	Figure 4 Install hand grip. See service manual. a. Align Twist Grip Sensor (TGS) tabs (2) with gaps in grip (1). b. Place grip in position. NOTE When installing Right Hand Control Module (RHCM), verify throttle end play is set correctly. See service manual.
2.	Figure 3 Place rear cover (3) in position.
3.	Tighten screws (2). Torque: 0.6–0.9 N·m (5–8 in-lbs)
4.	Figure 3 Install end cap (1). Tighten. Torque: 14–20 N·m (124–177 in-lbs) NOTE Check for free throttle movement.

1	End cap
2	Grip
3	Clamp screw

Figure 2. Left Side Grip (typical)

1	End cap
2	Screw (2)
3	Rear cover

Figure 3. Front Cover (left side shown)

1	Grip
2	TGS tab (2)

Figure 4. TGS Engagement