PREMIUM FITTED SADDLEBAG LINERS
941004032024-01-23
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
90202608 | Safety Glasses |  |
(1) Only simple tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Premium Fitted Saddlebag Liners
Table 2. Kit Contents: Premium Fitted Saddlebag Liners Kit
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Saddlebag liner, left | 93300177 | |
| 2 | 1 | Saddlebag liner, right | 93300178 | |
| 3 | 8 | Tape | Not sold separately | |
| 4 | 1 | Alcohol wipe | 94678-00Y | |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
REMOVE
| 1. | Open saddlebag lid. | |
| 2. | Figure 2 Remove mounting screws with lever (1). Retain for installation. |
| 1 | Mounting screw with lever (2) |
| 2 | Support bracket |
| 3 | Connector |
| 4 | Saddlebag rail |
Figure 2. Remove/Install Saddlebag
INSTALL
WARNINGDo not exceed saddlebag weight capacity. Put equal weight in each bag. Too much weight in saddlebags can cause loss of control, which could result in death or serious injury. (00383a)
NOTE
Maximum load capacity of the wall organizer is 1.36 kg (3 lb). Combined load of wall organizer and saddlebag must not exceed 6.8kg (14.99 lb).
| 1. | Figure 3 Clean back of saddlebag liner (1) using alcohol wipe and apply adhesive tape(2) where needed. | |
| 2. | Figure 4 Install saddlebag liner (4) into saddlebag (1). | |
| 3. | Align mounting hole of saddlebag liner (4) with saddlebag mounting location. | |
| 4. | Figure 2 Install mounting screw with lever (2). a. Turn lever (1) clockwise until secure. b. Lever should be pointed between 3 o'clock and 9 o'clock positions as shown. | |
| 5. | Verify saddlebag is secure. | |
| 6. | Close saddlebag lid. | |
| 7. | Repeat steps for opposite side. |
| 1 | Saddlebag liner |
| 2 | Tape |
Figure 3. Tape
| 1 | Saddlebag |
| 2 | Saddlebag liner |
| 3 | Mounting screw with lever (2) |
Figure 4. Install Saddlebag Liner
CARE AND MAINTENANCE INSTRUCTIONS
| 1. | Use a lint free cloth to wipe off any dust or dirt. | |
| 2. | Thoroughly clean outer surface with warm water and a mild detergent. | |
| 3. | Do not use artificial means to dry material quickly. | |
| 4. | Contains one or more of the following materials: a. Polyester b. Polypropylene c. Polyethylene d. Polyvinyl chloride |