0/0
HARLEY-DAVIDSON AUDIO POWERED BY ROCKFORD FOSGATE SECONDARY SUBWOOFER INSTALLATION KIT
941006082024-07-02
GENERAL INFORMATION
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
69203434
Safety Glasses, Torque Wrench
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Harley-Davidson Audio Powered By Rockford Fosgate Secondary Subwoofer Installation Kit
Table 2. Kit Contents: Harley-Davidson Audio Powered By Rockford Fosgate Secondary Subwoofer Installation Kit
Verify that all contents are present in the kit before installing or removing items from vehicle.
Item
Qty
Description
Part No.
Notes
1
6
Anchor, cable strap
69200342
2
8
Cable strap
10065
3
1
Internal harness with panel mount
Not sold separately
4
1
Template, drill
76001389
5
6
Screw, T15
10200065
6
1
Harness, secondary subwoofer
Not sold separately
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A Service Manual and Electrical Diagnostic Manual (EDM) for the year and model motorcycle is required for this installation.
  • These items are available at your local Harley-Davidson dealership.
  • Separate purchase of a Primary Subwoofer Kit (Part No. 76001376) is required for this installation.
  • Separate purchase of Secondary Amplifier Kit (Part No. 76001444) is required for this installation.
  • Separate purchase of a Secondary Subwoofer Kit (Part No. 76001377) is required for this installation.
Installation by a technician at a Harley-Davidson dealership is recommended.
To ensure proper audio performance, speaker set up in the Infotainment Control Unit (IFCU) OR Digital Technician II (DT II) is required for audio configuration and amplifier firmware update.
PREPARE
NOTE
Models with security: Disable security system. See service manual.
1. Remove left and right saddlebags. See service manual.
2. Remove left and right side covers. See service manual.
3. Remove main fuse. See service manual.
4. Remove seat. See service manual.
MODIFY SADDLEBAG
Vehicles Without Saddlebag Lid Speakers Only
NOTE
Drill template must lay flat against all saddlebag surfaces to position holes properly.
1. See Figure 2. Position drill template (1) on back of left saddlebag with orange side facing in toward saddlebag.
NOTE
Take extreme caution not to damage the painted surface.
It is recommended to mark holes with a soft tip marker, then measuring the marks with a scale or calipers to ensure proper hole alignment to the internal harness panel.
a. Install drill template (1) over rear mount grommet (2).
b. Follow contour (3) of saddlebag under grommet (2).
c. Fold drill template (5) over bottom of saddlebag where indicated.
d. Use tape (4) to secure drill template (1) in several locations.
2. Modify left saddlebag.
NOTE
Use extreme caution not to cut outside of connector hole perimeter to prevent a loose panel fit or improper gasket seal.
a. Center punch drill locations marked (A and B) on template.
b. Drill six mounting holes at location (A).
Diameter: 6 mm (¼ in)
c. Drill two connector pass thru holes at location (B).
Diameter: 70 mm (2¾ in)
d. De-burr edges of hole by lightly sanding the surface.
1Drill template
2Grommet
3Saddlebag contour
4Tape (4)
5Template fold
Figure 2. Drill Template (typical)
REMOVE
Vehicles Equipped With Panel Connectors
NOTE
Use caution as harness panel screws have lock patch and can easily be stripped.
1. Remove left saddlebag audio OE harness panel. See Service Manual.
2. Remove audio harness from interior of saddlebag.
INSTALL
1. Install harness panel.
a. See Figure 3. Install harness panel (5).
1.2. Install screws (6). Tighten.
Torque: 2.28–2.79 N·m (20.2–24.7 in-lbs)
1Harness
2Harness panel cover
3Secondary subwoofer connector [367B]
4Speaker connectors [37B] (2)
5Harness panel
6Screw (6)
Figure 3. Amplifier Harness Panel
2. If equipped with saddlebag lid speakers and/or power locks, see EDM. Others skip ahead to step 5.
a. See Figure 1. Original 6 way left saddlebag speaker/lock harness connector [288B] is replaced with the 8 way connector from secondary subwoofer harness (6).
b. Remove all wires from original 6 way left saddlebag harness connector [288B].
c. See Figure 4. Remove seal plugs from cavities 1 thru 4 (as required below) in new left saddlebag 8 way harness connector [288B].
d. If equipped with speakers, install LBE/O speaker wire into cavity 1 (1).
e. If equipped with speakers, install LBE/GY speaker wire into cavity 2 (2).
f. If equipped with power locks, insert TN/O power lock wire terminal into cavity 3 (3).
g. If equipped with power locks, insert TN/R power unlock wire terminal into cavity 4 (4).
1Cavity 1 LBE\O Wire speaker positive
2Cavity 2 LBE\R Wire speaker negative
3Cavity 3 TN\O Wire power lock
4Cavity 4 TN\R Wire power unlock
5Cavity 5 BN\GY Wire secondary subwoofer negative
6Cavity 6 BN\R Wire secondary subwoofer positive
7Cavity 7 BK Wire secondary subwoofer detect negative
8Cavity 8 GY Wire secondary subwoofer detect positive
Figure 4. Connector [288B] View
3. See Figure 1. If equipped with power locks, remove seal plugs from cavity 1 and 2 in left saddlebag, 8 way panel connector [288A] (3).
a. See Figure 5. Using audio/lock harness removed from saddlebag earlier, insert TN/O power lock wire terminal into cavity 3 (3).
b. Insert TN/R power unlock wire terminal into cavity 4 (4).
1Cavity 1 LBE\O Wire speaker positive
2Cavity 2 LBE\R Wire speaker negative
3Cavity 3 TN\O Wire power lock
4Cavity 4 TN\R Wire power unlock
5Cavity 5 BN\GY Wire secondary subwoofer negative
6Cavity 6 BN\R Wire secondary subwoofer positive
7Cavity 7 BK Wire secondary subwoofer detect negative
8Cavity 8 GY Wire secondary subwoofer detect positive
Figure 5. 8-Way Panel Connector [288A] View
4. Route power lock wires out the bottom of harness panel along audio harness.
5. See Figure 3. Install harness panel cover (2).
6. See Figure 3. Interior harness will be routed as shown. Anchors/cable straps and wire guides will be used when installing subwoofer kit.
7. See Figure 1. Install secondary subwoofer wire harness (6).
NOTE
If installing a with additional speaker kits, wait until all speaker components are installed prior to making any connections. See the appropriate speaker or harness kit installation instructions.
b. Mount saddlebag to check harness length. Leave enough length to easily connect to saddlebag.
c. Make certain harness will not contact any moving parts.
d. Tighten cable straps securing rear section of harness.
7.1. See Figure 6. Connect and route external wire harness along left rear frame rail. Using cable straps loosely install harness to anchor points (1). Do not tighten cable straps.
1Anchor point
2External wire harness connector [288B]
Figure 6. Harness Routing (Left)
8. Route harness forward between rear fender and frame into battery box area.
a. See Figure 7. Connect left saddlebag external harness connector [351B] to right saddlebag amp output harness connector [351A] (4) (both identified with blue tape).
1[325A_1] Rear PNA (12 way)
2[350A_1] A2B In (yellow tape)
3[350B_1] A2B Out (green tape)
4[351A_1] RH Amp Output (light blue and blue tape)
Figure 7. External Harness Underseat Routing Top View
9. See Figure 8. Route remaining left saddlebag exterior harness branch along right saddlebag amp harness and secure with cable straps.
a. Remove seal plug from cavity 5 and 6 of 6 way right saddlebag connector [289B].
b. Insert BK wire terminal into cavity 5 (1).
d. Reassemble harness connector [289B] into panel connector [289A].
9.3. Insert GY wire terminal into cavity 6 (2).
1Cavity 5 install BK wire
2Cavity 6 install GY wire
Figure 8. 6 Way Right Saddlebag Connector [289B]
10. Cap any unused connectors with seal plugs provided.
COMPLETE
NOTE
To prevent possible damage to the sound system, verify that the ignition is OFF before installing the main fuse.
Complete installation of all audio kits prior to performing these operations.
1. Install seat. After installing seat, pull up on the seat to verify that it is secure. See service manual.
2. Install main fuse. See service manual.
3. Install side covers. See service manual.
4. Install saddlebags. See service manual.
CONFIGURE
1. Perform system configuration ONLY after all audio accessory kits have been installed.
2. Power up vehicle in accessory mode.
3. On the Infotainment Control Unit (IFCU):
a. Select: Settings icon.
b. Select: Sounds Settings.
c. Follow on screen prompts for applicable audio system changes.
4. When complete, turn power off for 60 seconds.
5. Turn power back on, verify proper operation of audio system.