HARLEY-DAVIDSON AUDIO POWERED BY ROCKFORD FOSGATE - AMPLIFIER 600W 4-CHANNEL (SECONDARY)
941006092024-07-02
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
76001444 | Safety Glasses, Torque Wrench |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Harley-Davidson Audio Powered By Rockford Fosgate - Amplifier 600w 4-Channel (Secondary)
Table 2. Kit Contents: Harley-Davidson Audio Powered By Rockford Fosgate - Amplifier 600w 4-Channel (Secondary)
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Amplifier | not sold separately | |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation.
This item is available at a Harley-Davidson dealership.
- Separate purchase of Harley-Davidson Audio Powered by Rockford Fosgate Primary Subwoofer Installation Kit (Part No. 76001302) is required.
PREPARE
| 1. | Remove left saddlebag. See service manual. | |
| 2. | Remove left side cover. See service manual. | |
| 3. | Remove main fuse. See service manual. | |
| 4. | Open right saddlebag. |
INSTALL
| 1. | See Figure 3. Install amplifier (1) into housing. a. Use mounting post (3) to assist with alignment. b. Install screws (2). Tighten. Torque: 11.8–14.4 N·m (104–127 in-lbs) c. Connect connector (4) to amplifier (1). d. If equipped, route power lock harness out bottom of harness panel along audio harness. | |
| 2. | See Figure 2. Install amplifier cover (1). a. Verify tabs (3) are properly engaged. b. Install screws (2). Tighten. Torque: 0.73–0.89 N·m (6.5–7.9 in-lbs) |
COMPLETE
NOTE
To prevent possible damage to the sound system, verify that the ignition is OFF before installing the main fuse.
| 1. | Install main fuse. See service manual. | |
| 2. | Install left side cover. See service manual. | |
| 3. | Install left saddlebag. See service manual. |
SERVICE
| 1. | See Figure 2. Remove amplifier cover. a. Remove screws (2). b. Remove cover tabs (3) from housing. c. Remove cover (1). | 
Figure 2. Amplifier Cover (Secondary) | ||||||||
| 2. | See Figure 3. Remove amplifier. a. Remove screws (2). b. Disconnect connector (4). c. Remove amplifier (1). | 
Figure 3. Amplifier (Secondary) | ||||||||
| 3. | See Figure 3. Install amplifier (1) into housing. a. Use mounting post (3) to assist with alignment. b. Install screws (2). Tighten. Torque: 11.8–14.4 N·m (104–127 in-lbs) c. Connect connector (4) to amplifier (1). | |||||||||
| 4. | See Figure 2. Install amplifier cover (1). a. Verify tabs (3) are properly engaged. b. Install screws (2). Tighten. Torque: 0.73–0.89 N·m (6.5–7.9 in-lbs) |
CONFIGURE
| 1. | Perform system configuration ONLY after all audio accessory kits have been installed. | |
| 2. | Power up vehicle in accessory mode. | |
| 3. | On the Infotainment Control Unit (IFCU): a. Select: Settings icon. b. Select: Sounds Settings. c. Follow on screen prompts for applicable audio system changes. | |
| 4. | When complete, turn power off for 60 seconds. | |
| 5. | Turn power back on, verify proper operation of audio system. |