SCREAMIN' EAGLE MILWAUKEE-EIGHT™ STAGE 4 KIT
J064212020-03-23
GENERAL INFORMATION
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
92500060, 92500062, 92500064, 92500073, 92500076, 92500088
Safety Glasses, Torque Wrench
(1) Special tools or techniques required for installation
GENERAL
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Verify that the most current version of the instruction sheet is used. It is available at: www.harley-davidson.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
Visit https://serviceinfo.harley-davidson.com for the latest instruction sheet.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
    These items are available at your local Harley-Davidson dealership.
  • 2017-2018 Models with 107 Engine: Separate purchase of Screamin' Eagle High Capacity Clutch Plate kit (Part No. 37000258) is required.
  • 2017-2019 Models: Separate purchase of Oil Pump Assembly kit (Part No. 62400247-Oil Cooled or 62400248-Twin Cooled) is required.
  • Separate purchase of Screamin' Eagle High Flow Air Cleaner kit.
  • Separate purchase of the Cam Drive Retention Kit (Part No. 25566-06) is required.
  • Separate purchase of Cam Spacer Kit (Part No. 25928-06) is required.
  • Kit requires ECM recalibration. Contact a Harley-Davidson dealership.
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer.
PREPARE
1. Set motorcycle upright. See service manual.
2. Disarm security system. See service manual.
3. Remove seat. See service manual.
4. Remove main fuse. See service manual.
WARNING
When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a)
5. Remove fuel tank. See service manual.
6. Twin-Cooled: Drain coolant system.
REMOVE
NOTE
The following steps are provided as an outline process. Follow procedures in service manual.
1. Remove air cleaner assembly.
2. Remove exhaust system.
3. Remove induction module.
4. Disconnect harness connections from cylinder head.
5. Remove oil coolant lines and manifolds from engine.
6. Remove rocker covers, rocker arms, pushrods, and pushrod tubes.
7. Remove cylinder heads, cylinder and pistons.
8. Remove lifter covers, anti-rotation devices and lifters.
9. Remove cam cover, cam plate and camshaft.
10. Remove inner cam bearing.
11. Remove clutch unless already equipped with a 10 plate clutch. See service manual.
INSTALL
NOTE
The following steps are provided as an outline process. Follow procedures in service manual.
1. Install clutch using 10 plate clutch. See instruction sheet J06246 and service manual.
NOTE
10-plate assist and slip clutch used in Milwaukee-eight vehicles has sufficient capacity to support this kit for most applications. Only install higher capacity springs if clutch slippage occurs. Higher capacity springs will increase clutch lever effort.
2. Install camshaft needle bearing (5).
3. See Figure 3. Install oil pump.
4. Install camshaft into engine.
5. Assemble cam plate and camshaft drive.
6. Verify camshaft to crankshaft timing marks are properly aligned.
7. Install lifters (provided in kit), anti-rotation device, lifter cover gaskets (provided in kit) and lifter covers.
8. Install pistons and cylinders provided in kit. Follow instructions provided with piston and cylinder kit.
9. Install cylinder heads using new flange nuts included with kit. Follow instructions provided with cylinder head kit.
NOTE
This kit uses a special head torque sequence.
10. Install pushrod tubes and pushrods using O-rings provided with kit.
11. With piston at approximately Bottom Dead Center (BDC) on power stroke, install rocker arms.
12. Alternately tighten screws to pull rocker shaft down evenly.
13. Install rocker covers.
14. Verify that camshaft to crankshaft timing marks are properly aligned.
15. Install cam cover and new gasket provided in kit.
16. Prepare induction module included with kit for installation. See instructions included with induction module.
17. Install high flow fuel injectors.
18. Install induction module.
19. Install coolant/oil manifold to cylinder heads.
a. Thoroughly clean ALL threadlocking material from threads of screws and threaded holes. See service manual.
b. Clean all debris from mating surfaces.
c. Install O-rings provided in kit
20. Air-Cooled Touring models: Install fan assisted oil cooler included in kit.
21. Install exhaust system. See service manual.
22. Install air cleaner assembly. See instruction sheet included with separately purchased SE high flow air cleaner kit.
23. Install emissions label provided in kit.
a. Locate the emissions label on the frame tube below the handlebars.
b. Place the new partial label from this kit over the top portion of the emissions label on the frame tube.
24. Install new product information label included in kit.
a. Locate the VIN label on the frame tube below the handlebars.
b. For 2017 Touring models only: Place new product information label included in kits 92500060, 92500062 and 92500064 below VIN label on frame tube.
COMPLETE
1. Install fuel tank. See service manual.
2. Install main fuse. See service manual.
3. Twin-Cooled: Fill coolant system and purge air. See service manual.
4. Install seat. After installing seat, pull up on the seat to verify that it is secure. See service manual.
NOTICE
You must recalibrate the ECM when installing this kit. Failure to properly recalibrate the ECM can result in severe engine damage. (00399b)
5. Calibrate Electronic Control Module (ECM) with proper calibration for configuration. See dealer for details.
6. Run motorcycle until engine is at normal operating temperature. Repeat several times to verify proper operation.
7. See owner's manual for BREAK-IN RIDING RULES.
KIT CONTENTS
Figure 1. Kit Contents: Top End: Screamin' Eagle Milwaukee-Eight™ Stage 4 Components
Table 2. Kit Contents: Top End: Screamin' Eagle Milwaukee-Eight™ Stage 4 Components
Item
Qty
Description
Part No.
Notes
1
1
Piston kit, 114
21900084
2
1
Piston kit, 117
21900087
3
4
O-ring, coolant manifold
11900090
4
2
Exhaust gasket
65324-83B
5
4
Flange nut
10200303
6
1
Cylinder head kit, air cooled (HOG black)
16500512
7
1
Cylinder head kit, air cooled (black granite)
16500538
8
1
Cylinder head kit, twin-cooled (HOG black)
16500379
9
1
Cylinder head kit, twin-cooled (black granite)
16500527
10
1
Cylinder kit (HOG black)
16800120
11
1
Cylinder kit (black granite)
16800125
12
1
Cylinder kit (HOG black non-highlighted)
16800174
Notes:
  • For Piston kit (1,2) components, see instruction sheet J07056
  • For Cylinder kit (9,10,11) components see instruction sheet J06226
  • For Cylinder head kit (5,6,7) components see instruction sheet J06401
NOTE
Verify all contents are present in the kit before installing or removing items from vehicle.
KIT CONTENTS
Figure 2. Kit Contents: Valve Train: Screamin' Eagle Milwaukee-Eight™ Stage 4 Components
Table 3. Kit Contents: Valve Train: Screamin' Eagle Milwaukee-Eight™ Stage 4 Components
Item
Qty
Description
Part No.
Notes
1
4
O-ring
11293
2
4
O-ring
11132A
3
4
O-ring
11145A
4
2
Gasket, lifter cover
25700362
5
1
Lifter kit, high capacity
18572-13
6
2
Gasket, lower rocker cover
25700425
7
2
O-ring, breather
11900116
8
2
Gasket, upper rocker cover
25700372B
NOTE
Verify all contents are present in the kit before installing or removing items from vehicle.
KIT CONTENTS
Figure 3. Kit Contents: Cam Compartment: Screamin' Eagle Milwaukee-Eight™ Stage 4 Components
Table 4. Kit Contents: Cam Compartment: Screamin' Eagle Milwaukee-Eight™ Stage 4 Components
Item
Qty
Description
Part No.
Notes
1
1
Gasket, cam cover
25700370
2
1
Camshaft drive sprocket retention kit
25566-06
Purchase separately
3
1
O-ring, cam plate to oil pump
11900103
4
1
Camshaft, SE8-515
25400201
5
1
cam bearing
9298B
6
1
O-ring, oil pump to crankcase
11293
7
1
Oil pump (Oil cooled)
62400247
Purchased separately, if needed
1
Oil pump (Twin cooled)
62400248
Purchased separately, if needed
Items included but not shown
1
Screamin' Eagle 64mm throttle body kit
27200040
1
Screamin' Eagle high flow injection kit
27400040
1
Partial emissions tune-up label
Not sold separately
1
Product information label
Not sold separately
NOTE
Verify all contents are present in the kit before installing or removing items from vehicle.