HARLEY-DAVIDSON AUDIO POWERED BY ROCKFORD FOSGATE SECONDARY AMPLIFIER INSTALLATION KIT

941003682024-07-10

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
76001302	Safety Glasses, Torque Wrench

(1) Tightening to torque value or other moderate tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Harley-Davidson Audio Powered By Rockford Fosgate Secondary Amplifier Installation Kit

Table 2. Kit Contents: Harley-Davidson Audio Powered By Rockford Fosgate Secondary Amplifier Installation Kit

	Verify that all contents are present in the kit before installing or removing items from vehicle.
	Item	Qty	Description	Part No.	Notes
	1	1	Template, drill	76001389
	2	6	Screw, T15	10200065
	3	1	Internal harness with amp compartment	Not sold separately
	4	3	Screw, ¼-20	10200947
	5	1	Cover panel	Not sold separately
	6	3	Screw, self tapping	68042-99
	7	8	Anchor, cable strap	69200342
	8	10	Cable strap	10065
	9	1	Harness, accessory amplifier	69203486
	10	6	Seal pin	69203106
	11	1	Fuse, 40A	72371-95
	12	1	Housing, 6-way	72414-07BK
	13	1	External harness	Not sold separately
	14	1	Capacity label, saddlebag	14002201
Items mentioned in text, but not included in kit
	A	1	Amplifier, audio

GENERAL

Instruction sheet is also available electronically. To verify you are using the most current version available, do one of the following:

Go to h-d.com/isheets
Scan QR code in upper left corner of the instruction sheet

NOTE

This instruction sheet may have a Supplemental Video to assist installer in clarifying a certain part of the assembly. A linked video would be located at the end of this instruction sheet.

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

WARNING

Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)

NOTE

This instruction sheet references service manual information. A Service Manual and Electrical Diagnostic Manual (EDM) for the year and model motorcycle is required for this installation.

These items are available at your local Harley-Davidson dealership.

Separate purchase of a Primary Subwoofer Kit (Part No. 76001376) is required for this installation.
Separate purchase of Secondary Amplifier Kit (Part No. 76001444) is required for this installation.

Installation by a technician at a Harley-Davidson dealership is recommended.

To ensure proper audio performance, speaker set up in the Infotainment Control Unit (IFCU) OR Digital Technician II (DT II) is required for audio configuration and amplifier firmware update.

PREPARE

NOTE

Models with security: Disable security system. See service manual.

1.	Remove left and right saddlebags. See service manual.
2.	Remove left and right side covers. See service manual.
3.	Remove main fuse. See service manual.
4.	Remove seat. See service manual.
5.	Remove top caddy to gain access to battery. See service manual.

MODIFY SADDLEBAG

Vehicles Without Saddlebag Lid Speakers Only

NOTE

Drill template must lay flat against all saddlebag surfaces to position holes properly.

NOTE

Take extreme caution not to damage the painted surface.

It is recommended to mark holes with a soft tip marker, then measuring the marks with a scale or calipers to ensure proper hole alignment to the internal harness panel.

1.	Figure 2 Position drill template (1) on back of right saddlebag with orange side facing out. a. Install drill template (1) over rear mount grommet (2). b. Follow contour (3) of saddlebag under grommet (2). c. Fold drill template (5) over bottom of saddlebag where indicated. d. Use tape (4) to secure drill template (1) in several locations.
2.	NOTE Use extreme caution not to cut outside of connector hole perimeter to prevent a loose panel fit or improper gasket seal. Modify right saddlebag. a. Center punch drill locations marked (A and B) on template. b. Drill six mounting holes at location (A). Diameter: 6 mm (¼ in) c. Drill two connector pass thru holes at location (B). Diameter: 70 mm (2¾ in) d. De-burr edges of hole by lightly sanding the surface.
3.	Figure 1 Install saddlebag capacity label (14). a. Install over current label.

1	Drill template
2	Grommet
3	Saddlebag contour
4	Tape (4)
5	Template fold

Figure 2. Drill Template

REMOVE OE HARNESS PANEL

Vehicles Equipped With Saddlebag Lid Speakers Only

NOTE

Use caution as harness panel screws have lock patch and can easily be stripped.

1.	Remove right saddlebag audio OE harness panel. See Service Manual.
2.	Remove audio harness from interior of saddlebag.

INSTALL

Install secondary amplifier into harness panel. Installation Requirements

a. Follow instructions in that kit.

If equipped with power locks, see EDM.

a. If equipped with power locks, de-pin pock lock harness from Original Equipment Manufacturer (OEM) interior saddlebag harness.

b. Figure 3 Remove seal plugs from cavities 3 and 4 in new right saddlebag 6 way panel connector [289A].

c. Insert TN/O power lock wire terminal into cavity 3 (1).

d. Insert TN/R power unlock wire terminal into cavity 4 (2).

1	Cavity 3 TN\O Wire power lock
2	Cavity 4 TN\R Wire power unlock

Figure 3. 6 Way Panel Connector [289A] View

Install harness panel into saddlebag.

a. See Figure 4 and Figure 5. Install harness panel (2).

1	Screws (6)
2	Harness panel

Figure 5. Amplifier Harness Panel Installed

3.2.	Install screws (1). Tighten. Torque: 2.28–2.79 N·m (20.2–24.7 in-lbs)

1	Screws (6)
2	Harness panel
3	Amplifier

Figure 4. Amplifier Harness Panel

Figure 6 Verify that cable strap (1) is installed. If not, install cable strap to secure harnesses to panel as shown.

a. Route power lock wires out the bottom of harness panel along audio harness.

1	Cable strap

Figure 6. Amplifier Harness Panel Cable Strap

Figure 7 Install amplifier panel cover (1).

a. Verify tabs (3) are properly engaged.

5.2.	Install screws (2). Tighten. Torque: 0.73–0.89 N·m (6.5–7.9 in-lbs)

1	Amplifier cover
2	Screw (3)
3	Tab (2)

Figure 7. Amplifier Cover (Secondary)

Figure 8 Interior harness will be routed as shown. Anchors/cable straps and wire guides will be used when installing subwoofer kit.

1	Subwoofer connector
2	Saddlebag lid speaker positive connector (LBE wire)
3	Saddlebag lid speaker negative connector (LBE/BK wire)

Figure 8. Saddlebag Interior Wiring

NOTE

If installing a secondary amplifier with additional speaker kits, wait until all speaker components are installed prior to making any connections. See the appropriate speaker or harness kit installation instructions.

Figure 1 Install external harness (13).

a. See Figure 9 and Figure 10. Route external saddlebag harness along right rear frame rail. Using cable straps loosely install harness to anchor points (1). Do not tighten cable straps.

b. If equipped, connect 6 way connector [289B] to panel [289A] and secure with new external harness from kit.

c. Figure 1 If not equipped with saddlebag speakers or power locks, insert seal pins (10) into 6 way connector (12) and secure to panel connector [289A].

d. Mount saddlebag to check harness length. Leave enough length to easily connect to saddlebag.

e. Make certain harness will not contact any moving parts.

f. Tighten cable straps securing rear section of harness.

Route harness forward between rear fender and frame into battery box area.

a. See Figure 9 and Figure 11. Connect external harness connector [350A_1] to accessory amplifier harness connector [350B_1] (both with yellow tape).

1	[289B_2] Right saddlebag connector (16 way)
2	[43B] Amplifier fuse holder (40 amp fuse)
3	[351A_1] Audio out (light blue and blue tape)
4	[350B_1] A2B out (green tape)
5	[350A_1] A2B in (yellow tape)
6	Battery wire (+)
7	Battery wire (-)

Figure 9. External Harness Connectors

1	Anchor point
2	Rear fender strut

Figure 10. Rear Fender Strut

1	[325A_1] Rear PNA (12 way)
2	[350A_1] A2B In (yellow tape)
3	[350B_1] A2B Out (green tape)
4	[351A_1] RH Amp Output (light blue and blue tape)

Figure 11. External Harness Underseat Routing Top View

Figure 12 Remove fuse holder [43B] from weather cap.

a. Install 40A fuse into fuse holder [43B], install in weather cap and secure with cable strap to adjacent harness or frame.

b. Do not secure to brake lines.

10.

Route battery wire harness down and under Anti-lock Braking System (ABS) module, forward to the front of the battery tray. Battery positive branch is the longer of the two.

a. Connect negative battery wire.

10.2.

Connect positive battery wire.

1	[43B] Amplifier fuse holder (40 amp fuse)
2	Battery power (positive and negative)

Figure 12. External Harness Underseat Routing Right View

11.

Install top caddy. See service manual.

12.

Figure 1 Install accessory amplifier harness (9).

a. Figure 13 Remove weather plug from the 12 way harness connector [325A_1] (1) on top of battery tray.

12.2.

Insert connector [325B_1] into vehicle harness [325A_1] and route all branches as shown.

1	[325B_1] Harness Connector (12 way connector)
2	[350B_1] A2B out (yellow tape)
3	[325B_2] Rear PNA CAN/Power (orange tape)
4	[325B_3] Rear PNA Power (red tape)

Figure 13. Accessory Amplifier Harness

13.

Cap all unused connectors with seal plugs provided.

COMPLETE

NOTE

To prevent possible damage to the sound system, verify that the ignition is OFF before installing the main fuse.

NOTE

Complete installation of all audio kits prior to performing these operations.

1.	Install seat. After installing seat, pull up on the seat to verify that it is secure. See service manual.
2.	Install main fuse. See service manual.
3.	Install side covers. See service manual.
4.	Install saddlebags. See service manual.

CONFIGURE

NOTE

Update software in this order:

Step 1. Update Infotainment Control Unit (IFCU) software to the latest version.
Step 2. Update amplifier software to the latest version.

Do not proceed without performing these updates.

1.	From the www.harley-davidson.com website. a. Select: Software Updates. This links to Infotainment Support Resources. b. Select: Infotainment Control Unit (IFCU) Skyline^TM OS Located in Table of Content. c. Follow the instructions to transfer the update to the (IFCU) and Amplifiers as equipped.
2.	Perform system configuration ONLY after all audio accessory kits have been installed.
3.	Power up vehicle in accessory mode.
4.	On the Infotainment Control Unit (IFCU): a. Select: Settings icon. b. Select: Sounds Settings. c. Follow on screen prompts for applicable audio system changes.
5.	When complete, turn power off for 60 seconds.
6.	Turn power back on, verify proper operation of audio system.

NOTE

If audio system has subwoofer (s) connected, operated at full volume and subwoofer gain level 10 at idle for an extended period of time, battery voltage can drop and system may go into load shed mode with reduced performance until adequate battery state of charge is restored.